Re: Migrate from AIX 5.1 ML8 to 5.2
From: Chafik,Basim (basim.chafik_at_PLX.COM)
Date: 07/22/05
- Previous message: William Capeless: "Re: Migrate from AIX 5.1 ML8 to 5.2"
- Maybe in reply to: William Capeless: "Migrate from AIX 5.1 ML8 to 5.2"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Fri, 22 Jul 2005 05:57:42 -0700 To: aix-l@Princeton.EDU
Probably they did not fix it. I know that we received LCD4-1133-04 and the
problem is fixed in the edition of the CDs. You should be able to order them
from you rep or IBM support?
The problem you have is exactly what we had when upgrading from 5.1 to 5.2
Basim Chafik
Senior Systems Analyst
IBM Certified Advanced Technical Expert (CATE)
1.800.688.4895
basim.chafik@plx.com
plexus (Division of BancTec)
-----Original Message-----
From: William Capeless [mailto:CAPELW@MMC.ORG]
Sent: Friday, July 22, 2005 8:35 AM
To: aix-l@Princeton.EDU
Subject: Re: Migrate from AIX 5.1 ML8 to 5.2
Basim, Thanks for the response. I checked my CD's, and the (serial?) # on it
is LCD4-1133-02.
Do you know if the -02 CD's had the same bug or could it be a new and
improved bug??????
Are V5.2 CD's still available?
Thanks, Bill
William Capeless
System Software Specialist
Maine Medical Center
22 Bramhall St.
Portland, Maine 04102
(207) 662-6512
capelw@mmc.org <mailto:capelw@mmc.org>
>>> basim.chafik@PLX.COM 7/21/2005 1:51:40 PM >>>
Bill,
You have to replace your AIX 5.2 media with a new one. The Edition that you
have (LCD4-1133-01) has a bug. You will have this problem when upgrade but
not with fresh install. Basically the CD is missing the lsvg command which
the script use to determine the PP size.
I had the same problem.
Basim Chafik
Senior Systems Analyst
IBM Certified Advanced Technical Expert (CATE)
1.800.688.4895
basim.chafik@plx.com
plexus (Division of BancTec)
-----Original Message-----
From: William Capeless [mailto:CAPELW@MMC.ORG]
Sent: Thursday, July 21, 2005 1:36 PM
To: aix-l@Princeton.EDU
Subject: Migrate from AIX 5.1 ML8 to 5.2
I am trying to migrate my 7046-B50 from AIX 5.1 ml08 to 5.2(CD's dated
05/2003)
I get the message
"The boot logical volume(HD5) must be at least 8 meg
The system you are installing has a boot logical volume of less than this
and the system
does not have enough free contiguous physical partitions on hdisk0 to
increase the size
of the boot logical volume"
When I try to continue, the systems just hangs with the LED's of "0c32".
My hd5 is 32 meg, and there are 53 free contiguous partitions following HD5
on hdisk0.
Has anyone else had a similar problem and/or any idea's? LSPV & LSLV are
below
Thanks, Bill
>lspv -M hdisk0
hdisk0:1 hd5:1
hdisk0:2 hd5:2
hdisk0:3-55
hdisk0:56 hd1:253
hdisk0:57 hd1:254
hdisk0:58 hd1:255
....
>lslv hd5
LOGICAL VOLUME: hd5 VOLUME GROUP: rootvg
LV IDENTIFIER: 0001738f00004c0000000103665ccc6b.1 PERMISSION:
read/write
VG STATE: active/complete LV STATE: closed/syncd
TYPE: boot WRITE VERIFY: off
MAX LPs: 512 PP SIZE: 16 megabyte(s)
COPIES: 1 SCHED POLICY: parallel
LPs: 2 PPs: 2
STALE PPs: 0 BB POLICY: relocatable
INTER-POLICY: minimum RELOCATABLE: no
INTRA-POLICY: edge UPPER BOUND: 1
MOUNT POINT: N/A LABEL: None
MIRROR WRITE CONSISTENCY: on/ACTIVE
EACH LP COPY ON A SEPARATE PV ?: yes
William Capeless
System Software Specialist
Maine Medical Center
22 Bramhall St.
Portland, Maine 04102
(207) 662-6512
capelw@mmc.org <mailto:capelw@mmc.org>
- Previous message: William Capeless: "Re: Migrate from AIX 5.1 ML8 to 5.2"
- Maybe in reply to: William Capeless: "Migrate from AIX 5.1 ML8 to 5.2"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
