5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R

From: Stephane Raimbault (segr_at_hotmail.com)
Date: 10/30/03

Next message: Kris Kennaway: "Re: 5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R"

Previous message: Scott Long: "Re: __fpclassifyd problem"
Next in thread: Kris Kennaway: "Re: 5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R"
Reply: Kris Kennaway: "Re: 5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R"
Maybe reply: Stephane Raimbault: "Re: 5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

To: <current@freebsd.org>
Date: Wed, 29 Oct 2003 16:07:27 -0700

Hi,

I'm trying to install 5.1-R or 5.1-C from floppies redirected output to serial port and it won't boot to the install screen. 4.9-R floppies with output redirected to serial port works and installs properly. This is what I get on my serial console when I try to boot on 5.1-C (similar to 5.1-R) seems to hang after the vga0 shows up during boot.

Is there anything I can do or provide to resolve my install problem?

Uncompressing ... done
Console: serial port
BIOS drive A: is disk0
BIOS drive C: is disk1
BIOS 633kB/4061120kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root@ushi.jp.freebsd.org, Wed Oct 29 04:14:01 GMT 2003)
> include /boot/device.hints
> set hint.fdc.0.at="isa"
> set hint.fdc.0.port="0x3F0"
> set hint.fdc.0.irq="6"
> set hint.fdc.0.drq="2"
> set hint.fd.0.at="fdc0"
> set hint.fd.0.drive="0"
> set hint.fd.1.at="fdc0"
> set hint.fd.1.drive="1"
> set hint.ata.0.at="isa"
> set hint.ata.0.port="0x1F0"
> set hint.ata.0.irq="14"
> set hint.ata.1.at="isa"
> set hint.ata.1.port="0x170"
> set hint.ata.1.irq="15"
> set hint.adv.0.at="isa"
> set hint.adv.0.disabled="1"
> set hint.bt.0.at="isa"
> set hint.bt.0.disabled="1"
> set hint.aha.0.at="isa"
> set hint.aha.0.disabled="1"
> set hint.aic.0.at="isa"
> set hint.aic.0.disabled="1"
> set hint.atkbdc.0.at="isa"
> set hint.atkbdc.0.port="0x060"
> set hint.atkbd.0.at="atkbdc"
> set hint.atkbd.0.irq="1"
> set hint.atkbd.0.flags="0x1"
> set hint.psm.0.at="atkbdc"
> set hint.psm.0.irq="12"
> set hint.vga.0.at="isa"
> set hint.sc.0.at="isa"
> set hint.sc.0.flags="0x100"
> set hint.vt.0.at="isa"
> set hint.vt.0.disabled="1"
> set hint.apm.0.disabled="1"
> set hint.apm.0.flags="0x20"
> set hint.pcic.0.at="isa"
> set hint.pcic.0.port="0x3e0"
> set hint.pcic.0.maddr="0xd0000"
> set hint.pcic.1.at="isa"
> set hint.pcic.1.irq="11"
> set hint.pcic.1.port="0x3e2"
> set hint.pcic.1.maddr="0xd4000"
> set hint.pcic.1.disabled="1"
> set hint.sio.0.at="isa"
> set hint.sio.0.port="0x3F8"
> set hint.sio.0.flags="0x10"
> set hint.sio.0.irq="4"
> set hint.sio.1.at="isa"
> set hint.sio.1.port="0x2F8"
> set hint.sio.1.irq="3"
> set hint.sio.2.at="isa"
> set hint.sio.2.disabled="1"
> set hint.sio.2.port="0x3E8"
> set hint.sio.2.irq="5"
> set hint.sio.3.at="isa"
> set hint.sio.3.disabled="1"
> set hint.sio.3.port="0x2E8"
> set hint.sio.3.irq="9"
> set hint.ppc.0.at="isa"
> set hint.ppc.0.irq="7"
> set hint.ed.0.at="isa"
> set hint.ed.0.disabled="1"
> set hint.ed.0.port="0x280"
> set hint.ed.0.irq="10"
> set hint.ed.0.maddr="0xd8000"
> set hint.cs.0.at="isa"
> set hint.cs.0.disabled="1"
> set hint.cs.0.port="0x300"
> set hint.sn.0.at="isa"
> set hint.sn.0.disabled="1"
> set hint.sn.0.port="0x300"
> set hint.sn.0.irq="10"
> set hint.ie.0.at="isa"
> set hint.ie.0.disabled="1"
> set hint.ie.0.port="0x300"
> set hint.ie.0.irq="10"
> set hint.ie.0.maddr="0xd0000"
> set hint.fe.0.at="isa"
> set hint.fe.0.disabled="1"
> set hint.fe.0.port="0x300"
> set hint.le.0.at="isa"
> set hint.le.0.disabled="1"
> set hint.le.0.port="0x300"
> set hint.le.0.irq="5"
> set hint.le.0.maddr="0xd0000"
> set hint.lnc.0.at="isa"
> set hint.lnc.0.disabled="1"
> set hint.lnc.0.port="0x280"
> set hint.lnc.0.irq="10"
> set hint.lnc.0.drq="0"
> load /kernel
/kernel text=0x23b500 data=0x2f024+0x4bedc /
> echo \007\007

> echo Please insert MFS root floppy and press enter:
Please insert MFS root floppy and press enter:
> read

> load -t mfs_root /mfsroot
> set hint.acpi.0.disabled=1
> set driver_floppy=YES
> set module_path="/modules;/dist"
> echo \007\007

> autoboot 10
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/kernel]...
131072K of memory above 4GB ignored
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT-20031029-JPSNAP #0: Wed Oct 29 04:30:49 GMT 2003
    root@ushi.jp.freebsd.org:/usr/obj/usr/src/sys/BOOTMFS
Preloaded elf kernel "/kernel" at 0xc0af1000.
Preloaded mfs_root "/mfsroot" at 0xc0af12c0.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(TM) CPU 2.40GHz (2399.33-MHz 686-class CPU)
  Origin = "GenuineIntel" Id = 0xf25 Stepping = 5
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory = 4160225280 (3967 MB)
avail memory = 4043710464 (3856 MB)
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 4423680 bytes at 0xc06b7400
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcibios: BIOS version 2.10
Using $PIR table, 29 entries at 0xc00fddf0
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci_cfgintr: 0:29 INTA BIOS irq 11
pci_cfgintr: 0:29 INTB BIOS irq 10
pci_cfgintr: 0:29 INTC BIOS irq 5
pci0: <unknown> at device 0.1 (no driver attached)
pcib1: <PCIBIOS PCI-PCI bridge> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <base peripheral, interrupt controller> at device 28.0 (no driver attached)
pcib2: <PCIBIOS PCI-PCI bridge> at device 29.0 on pci1
pci2: <PCI bus> on pcib2
pci1: <base peripheral, interrupt controller> at device 30.0 (no driver attached)
pcib3: <PCIBIOS PCI-PCI bridge> at device 31.0 on pci1
pci3: <PCI bus> on pcib3
pci_cfgintr: 3:2 INTA BIOS irq 11
pci_cfgintr: 3:2 INTB BIOS irq 11
pci3: <network, ethernet> at device 2.0 (no driver attached)
pci3: <network, ethernet> at device 2.1 (no driver attached)
pcib4: <PCIBIOS PCI-PCI bridge> at device 3.0 on pci0
pci4: <PCI bus> on pcib4
pci4: <base peripheral, interrupt controller> at device 28.0 (no driver attached)
pcib5: <PCIBIOS PCI-PCI bridge> at device 29.0 on pci4
pci5: <PCI bus> on pcib5
pci4: <base peripheral, interrupt controller> at device 30.0 (no driver attached)
pcib6: <PCIBIOS PCI-PCI bridge> at device 31.0 on pci4
pci6: <PCI bus> on pcib6
pci_cfgintr: 6:1 INTA BIOS irq 12
asr0: <Adaptec Caching SCSI RAID> mem 0xfc000000-0xfdffffff,0xfb000000-0xfbffffff,0xf8400000-0xf84fffff irq 12 at device 1.0 on pci6
asr0: major=154
asr0: ADAPTEC 2010S FW Rev. 3B05, 2 channel, 256 CCBs, Protocol I2O
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x2000-0x201f irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x2020-0x203f irq 10 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x2040-0x205f irq 5 at device 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib7: <PCIBIOS PCI-PCI bridge> at device 30.0 on pci0
pci7: <PCI bus> on pcib7
pci_cfgintr: 7:1 INTA BIOS irq 11
pci7: <display, VGA> at device 1.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x2060-0x206f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
orm0: <Option ROMs> at iomem 0xe0000-0xe3fff,0xdc000-0xdffff,0xc9000-0xcefff,0xc8000-0xc8fff,0xc0000-0xc7fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0

_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"

Next message: Kris Kennaway: "Re: 5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R"

Previous message: Scott Long: "Re: __fpclassifyd problem"
Next in thread: Kris Kennaway: "Re: 5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R"
Reply: Kris Kennaway: "Re: 5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R"
Maybe reply: Stephane Raimbault: "Re: 5.1-R and 5.1-C floppies will not boot on SuperMicro 6023P-8R"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Relevant Pages

Re: Corrupt data - RAID sata_sil 3114 chip
... As far as the cache line size register, ... This patch set default values for the FIFO PCI Bus Arbitration to ... Taking "lspci -nnvvvxxx" output of before and after such BIOS update ... I'm CCing Carlos Pardo at Silicon Image who wrote the patch above, ...
(Debian-User)
Re: Corrupt data - RAID sata_sil 3114 chip
... As far as the cache line size register, ... This patch set default values for the FIFO PCI Bus Arbitration to ... Taking "lspci -nnvvvxxx" output of before and after such BIOS update ... Might be my colleague, who wrote that tool, recently broke something (as it is the second time, it doesn't report corruptions), in the past it did work reliably. ...
(Debian-User)
Re: TESTERS WANTED for ATAng preview 1
... Console: serial port ... BIOS 639kB/523264kB available memory ... Preloaded elf kernel "/boot/kernel/kernel" at 0xc041b000. ... pci0: <PCI bus> on pcib0 ...
(freebsd-current)
Re: Compaq Deskpro 4000 nic
... options like that in the bios. ... > information about all the hardware on the PCI bus. ... > NIC says it has IRQ 0, that means the BIOS didn't assign an IRQ to the ... > PCI card, so you'll have to force the BIOS to set things up properly by ...
(comp.os.linux.hardware)
Re: Bios will not initialize my video
... I replaced my BIOS battery and my time certainly got fixed. ... the video not initializing problem is still there. ... Another possibility is an IRQ conflict with the Adaptec 29160, which might explain why the monitor comes up right as the Adaptec 29160 BIOS runs. ... PCI bus 1 slot 1 = INTA ADD additional routing! ...
(alt.comp.hardware.pc-homebuilt)