CF cards / ATAng / interrupt code still broken
From: Marco Wertejuk (wertejuk_at_mwcis.com)
Date: 11/16/03
- Previous message: Matt Douhan: "Re: make options target in bsd.port.mk"
- Next in thread: M. Warner Losh: "Re: CF cards / ATAng / interrupt code still broken"
- Reply: M. Warner Losh: "Re: CF cards / ATAng / interrupt code still broken"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Sun, 16 Nov 2003 23:34:28 +0100 To: current@freebsd.org
Hello,
as reproducable seen on my IBM Thinkpad, current as of some days
ago has problems to boot with my 128MB noname CF card inserted.
The panic output is very similar the problem Alex Dupre reported
in mid of september, but Sorens patch which should be tried to
get this stuff fixed but the patch does not help.
These messages get logged while booting verbose:
(... beginning removed because it's probably not interesting)
pccard0: CIS version PCCARD 2.0 or 2.1
pccard0: CIS info: CF, 128MB,
pccard0: Manufacturer code 0xa, product 0x0
pccard0: function 0: fixed disk, ccr addr 200 mask f
pccard0: function 0, config table entry 0: memory card; irq mask 0; memspace 0-7ff; mwait_required rdybsy_active powerdown
pccard0: function 0, config table entry 1: I/O card; irq mask ffff; iomask 4, iospace 0-f; memspace 0-7ff; rdybsy_active io8 io16 irqshare irqpulse irqlevel powerdown
pccard0: function 0, config table entry 2: I/O card; irq mask 4000; iomask a, iospace 1f0-1f7 3f6-3f7; memspace 0-7ff; rdybsy_active io8 io16 irqshare irqpulse irqlevel powerdown
pccard0: function 0, config table entry 3: I/O card; irq mask 4000; iomask a, iospace 170-177 376-377; memspace 0-7ff; rdybsy_active io8 io16 irqshare irqpulse irqlevel powerdown
pccard0: Allocation failed for cfe 0
ata2: <CF 128MB> at port 0x100-0x10f irq 11 function 0 config 1 on pccard0
ata2: reset tp1 mask=01 ostat0=50 ostat1=b7
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 mask=01 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata2: spurious interrupt - status=0x50 error=0x01
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: setting PIO4 on Intel PIIX4 chip
ata0-master: setting UDMA33 on Intel PIIX4 chip
GEOM: create disk ad0 dp=0xc2972b60
ad0: <TOSHIBA MK6021GAS/GA023A> ATA-5 disk at ata0-master
ad0: 57231MB (117210240 sectors), 116280 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
GEOM: new disk ad0
ata2-master: pio=0x08 wdma=0xffffffff udma=0xffffffff cable=40pin
ad4: FAILURE - SETFEATURES status=51<READY,DSC,ERROR> error=4<ABORTED>
ad4: FAILURE - SETFEATURES status=51<READY,DSC,ERROR> error=4<ABORTED>
GEOM: create disk ad4 dp=0xc297a260
ad4: <^A/.65> ATA-0 disk at ata2-master
Fatal trap 18: integer divide fault while in kernel mode
instruction pointer = 0x8:0xc06650cb
stack pointer = 0x10:0xc0821c2c
frame pointer = 0x10:0xc0821cac
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 0 (swapper)
kernel: type 18 trap, code=0
Stopped at __qdivrem+0x3b: divl %ecx,%eax
db> trace
__qdivrem(0,0,0,0,0) at __qdivrem+0x3b
__udivdi3(0,0,0,0,0) at __udivdi3+0x2e
ad_print(c297a200,c297a260,1,0,0,0,f,c2a0a400,0,0) at ad_print+0xbd
ad_attach(c2a0a4a4,2,c1292040,c06d1650,c0821d80) at ad_attach+0x40b
ata_boot_attach(0,826000,c0821d80,c0504e2a,0) at ata_boot_attach+0x47
run_interrupt_driven_config_hooks(0,81e000,81ec00,81e000,0) at run_interrupt_driven_config_hooks+0x2b
mi_startup() at mi_startup+0xb5
begin() at begin+0x2c
db>
If I insert the card after the system is up and running the
panic does not appear, probably because ATAng does not get
the information about a newly inserted drive?
At least atacontrol list does not display any drives:
desire:~>sudo atacontrol list
ATA channel 0:
Master: ad0 <TOSHIBA MK6021GAS/GA023A> ATA/ATAPI rev 5
Slave: no device present
ATA channel 1:
Master: no device present
Slave: no device present
ATA channel 2:
Master: no device present
Slave: no device present
If there are further patches available I would like to test
them in order to use my CF card again ;)
-- Mit freundlichen Gruessen, Marco Wertejuk - mwcis.com Consulting & Internet Solutions _______________________________________________ freebsd-current@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
- Previous message: Matt Douhan: "Re: make options target in bsd.port.mk"
- Next in thread: M. Warner Losh: "Re: CF cards / ATAng / interrupt code still broken"
- Reply: M. Warner Losh: "Re: CF cards / ATAng / interrupt code still broken"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
