The reboot doesn't work anymore in today -CURRENT..
From: Jeremy Messenger (mezz7_at_cox.net)
Date: 12/19/03
- Previous message: Tinderbox: "[current tinderbox] failure on sparc64/sparc64"
- Next in thread: Joe Marcus Clarke: "Re: The reboot doesn't work anymore in today -CURRENT.."
- Reply: Joe Marcus Clarke: "Re: The reboot doesn't work anymore in today -CURRENT.."
- Reply: UDSD387: ""Me too" re: The reboot doesn't work anymore in today -CURRENT.."
- Reply: pseniura_at_techie.com: ""Me too" addendum re: The reboot doesn't work anymore in today -CURRENT.."
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Thu, 18 Dec 2003 23:16:53 -0600 To: freebsd-current@freebsd.org
Yesterday and today, I CVSup'ed and the reboot doesn't work anymore,
something isn't work correct. The last week -CURRENT works fine, I can
reboot. I tried to use GENERIC kernel and I still get the same result, so
I am not sure what I should do next. Attaching the dmesg.txt here..
shutdown's -r and -p don't work, I had to press the power button to turn
off and on by manual. It does shutdown clean like 'shutdown -h', thought.
======================================
# shutdown -r now
[...]
syncing disk, buffers remaining... 2 2
done
Uptime: 3m24s
[...halting here forever...]
Debugger("manual escape to debugger")
Stopped at Debugger+0x4e: xchgl %ebx,in_Debuger,0
db> trace
Debugger(c085f94a,4,1,0,1) at Debugger+0x4e
scgetc(c0952420,0,c0845e32,c2dc6780) at scgetc+0x41f
sckbdevent(c09393a0,0,c0952420,c0625cb2,c0901ca0) at sckbdevent+0x1d0
atkbd_intr(c09393a0,0,cdcbdd14,c061c102,c09393a0) at atkbd_intr+0x2c
atkbd_isa_intr(c09393a0,0,c08433e7,21f,c16c68d4) at atkbd_isa_intr+0x21
ithread_loop(c16c4500,cdcbdd48,c084324d,311,c16c4500) at ithread_loop+0x172
fork_exit(c061bf90,c16c4500,cdcbdd48) at fork_exit+0xb4
fork_trampoline() at fork_trampoline+0x8
--- trap 0x1, eip = 0, esp = 0xcdcbdd7c, ebp = 0 ---
db>
======================================
Note: I copied above by hand.
Cheers,
Mezz
-- bsdforums.org 's moderator, mezz.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-CURRENT #0: Thu Dec 18 21:49:18 CST 2003
mezz@mezz.mezzweb.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a84000.
Preloaded elf module "/boot/kernel/linux.ko" at 0xc0a841f4.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a842a0.
Calibrating clock(s) ... i8254 clock: 1193242 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1666733799 Hz
CPU: AMD Athlon(tm) XP (1666.73-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x662 Stepping = 2
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0400000<AMIE,DSP,3DNow!>
Data TLB: 32 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory = 268369920 (255 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c29000 - 0x000000000fb49fff, 250744832 bytes (61217 pages)
avail memory = 251043840 (239 MB)
bios32: Found BIOS32 Service Directory header at 0xc00fae40
bios32: Entry = 0xfb2a0 (c00fb2a0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb2d0
pnpbios: Found PnP BIOS data at 0xc00fbc70
pnpbios: Entry = f0000:bca0 Rev = 1.0
Other BIOS signatures found:
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <761686 MSI ACPI> on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003840
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=700e1022)
pcibios: BIOS version 2.10
Using $PIR table, 8 entries at 0xc00fdcb0
PCI-Only Interrupts: 5 10 11
Location Bus Device Pin Link IRQs
slot 1 0 9 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 1 0 9 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 1 0 9 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 1 0 9 D 0x05 3 4 5 7 9 10 11 12 14 15
slot 2 0 10 A 0x02 3 4 5 7 9 10 11 12 14 15
slot 2 0 10 B 0x03 3 4 5 7 9 10 11 12 14 15
slot 2 0 10 C 0x05 3 4 5 7 9 10 11 12 14 15
slot 2 0 10 D 0x01 3 4 5 7 9 10 11 12 14 15
slot 3 0 11 A 0x03 3 4 5 7 9 10 11 12 14 15
slot 3 0 11 B 0x05 3 4 5 7 9 10 11 12 14 15
slot 3 0 11 C 0x01 3 4 5 7 9 10 11 12 14 15
slot 3 0 11 D 0x02 3 4 5 7 9 10 11 12 14 15
slot 4 0 12 A 0x05 3 4 5 7 9 10 11 12 14 15
slot 4 0 12 B 0x01 3 4 5 7 9 10 11 12 14 15
slot 4 0 12 C 0x02 3 4 5 7 9 10 11 12 14 15
slot 4 0 12 D 0x03 3 4 5 7 9 10 11 12 14 15
slot 5 0 13 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 5 0 13 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 5 0 13 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 5 0 13 D 0x05 3 4 5 7 9 10 11 12 14 15
slot 6 1 5 A 0x02 3 4 5 7 9 10 11 12 14 15
slot 6 1 5 B 0x03 3 4 5 7 9 10 11 12 14 15
slot 6 1 5 C 0x05 3 4 5 7 9 10 11 12 14 15
slot 6 1 5 D 0x01 3 4 5 7 9 10 11 12 14 15
embedded 0 1 A 0x02 3 4 5 7 9 10 11 12 14 15
embedded 0 1 B 0x03 3 4 5 7 9 10 11 12 14 15
embedded 0 1 C 0x05 3 4 5 7 9 10 11 12 14 15
embedded 0 1 D 0x01 3 4 5 7 9 10 11 12 14 15
embedded 0 7 C 0x03 3 4 5 7 9 10 11 12 14 15
embedded 0 7 D 0x05 3 4 5 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x6000-0x607f,0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.0
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.1
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.2
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.3
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.10.0
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.10.1
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.10.2
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.10.3
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.0
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.1
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.2
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.3
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.12.0
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.12.1
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.12.2
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.12.3
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.0
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.1
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.2
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.3
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.0
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.1
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.2
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.3
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.1
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3
---- before setting priority for links ------------
\\_SB_.PCI0.LNKA:
interrupts: 1 3 4 5 6 7 10 11 12 14 15
penalty: 100880 1880 1880 1680 1880 1880 1680 1680 1880 10880 10880
references: 8
priority: 0
---- before fixup boot-disabled links -------------
\\_SB_.PCI0.LNKA:
interrupts: 1 3 4 5 6 7 10 11 12 14 15
penalty: 100880 1880 1880 1680 1880 1880 1680 1680 1880 10880 10880
references: 8
priority: 99694
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.0
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.1
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.2
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.3
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.10.0
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.10.1
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.10.2
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.10.3
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.0
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.1
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.2
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.3
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.12.0
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.12.1
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.12.2
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.12.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.0
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.1
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.2
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.3
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.0
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.1
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.2
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.1
\\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2
\\_SB_.PCI0.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base d0000000, size 27, enabled
map[14]: type 3, range 32, base e3001000, size 12, enabled
map[18]: type 4, range 32, base 0000c000, size 2, port disabled
found-> vendor=0x1022, dev=0x700e, revid=0x13
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x700f, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0e (3500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0686, revid=0x40
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000c400, size 4, enabled
found-> vendor=0x1106, dev=0x0571, revid=0x06
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000c800, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 11
found-> vendor=0x1106, dev=0x3038, revid=0x16
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000cc00, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 11
found-> vendor=0x1106, dev=0x3038, revid=0x16
bus=0, slot=7, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x3057, revid=0x40
bus=0, slot=7, func=4
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000d000, size 8, enabled
map[14]: type 4, range 32, base 0000d400, size 2, enabled
map[18]: type 4, range 32, base 0000d800, size 2, enabled
pcib0: matched entry for 0.7.INTC (source \\_SB_.PCI0.LNKC)
pcib0: slot 7 INTC is routed to irq 10
found-> vendor=0x1106, dev=0x3058, revid=0x50
bus=0, slot=7, func=5
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000e000, size 8, enabled
map[14]: type 1, range 32, base e3000000, size 10, enabled
pcib0: matched entry for 0.12.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 12 INTA is routed to irq 11
found-> vendor=0x1317, dev=0x0985, revid=0x11
bus=0, slot=12, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x80 (32000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e400, size 8, enabled
map[14]: type 1, range 64, base e3002000, size 12, enabled
pcib0: matched entry for 0.15.INTA (source \\_SB_.PCI0.LNKC)
pcib0: slot 15 INTA is routed to irq 10
found-> vendor=0x9005, dev=0x00cf, revid=0x01
bus=0, slot=15, func=0
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000e800, size 8, enabled
map[14]: type 1, range 64, base e3003000, size 12, enabled
pcib0: matched entry for 0.15.INTB (source \\_SB_.PCI0.LNKD)
pcib0: slot 15 INTB is routed to irq 11
found-> vendor=0x9005, dev=0x00cf, revid=0x01
bus=0, slot=15, func=1
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
agp0: <AMD 761 host to AGP bridge> port 0xc000-0xc003 mem 0xe3001000-0xe3001fff,0xd0000000-0xd7ffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 128M
agp0: gatt -> ag_pdir 0x218000
agp0: allocating GATT for 32768 AGP page entries
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xe0000000-0xe1ffffff
pcib1: prefetched decode 0xd8000000-0xdfffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 1, range 32, base e0000000, size 24, enabled
map[14]: type 3, range 32, base d8000000, size 27, enabled
pci_cfgintr_valid: BIOS irq 5 is valid
pci_cfgintr: 1:5 INTA BIOS irq 5
found-> vendor=0x10de, dev=0x0281, revid=0xa1
bus=1, slot=5, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
pci1: <display, VGA> at device 5.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686B UDMA100 controller> port 0xc400-0xc40f at device 7.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=01
ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0-slave: stat=0x01 err=0x08 lsb=0x14 msb=0xeb
ata0: reset tp2 mask=03 stat0=00 stat1=01 devices=0x4<ATAPI_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0xc800-0xc81f irq 11 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
uhub0: port error, restarting port 2
uhub0: port error, giving up port 2
uhci1: <VIA 83C572 USB controller> port 0xcc00-0xcc1f irq 11 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub1: port error, restarting port 1
uhub1: port error, giving up port 1
uhub1: port error, restarting port 2
uhub1: port error, giving up port 2
pci0: <serial bus, SMBus> at device 7.4 (no driver attached)
pci0: <multimedia, audio> at device 7.5 (no driver attached)
dc0: <ADMtek AN985 10/100BaseTX> port 0xe000-0xe0ff mem 0xe3000000-0xe30003ff irq 11 at device 12.0 on pci0
dc0: Ethernet address: 00:04:5a:79:36:96
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x000749, model 0x0001, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc0: bpf attached
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xe400-0xe4ff mem 0xe3002000-0xe3002fff irq 10 at device 15.0 on pci0
ahc0: Defaulting to MEMIO off
ahc0: Reading SEEPROM...done.
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 423 instructions downloaded
ahc0: Features 0x1fef6, Bugs 0x40, Flags 0x20485560
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xe800-0xe8ff mem 0xe3003000-0xe3003fff irq 11 at device 15.1 on pci0
ahc1: Defaulting to MEMIO off
ahc1: Reading SEEPROM...done.
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Secondary High byte termination Enabled
ahc1: Secondary Low byte termination Enabled
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 423 instructions downloaded
ahc1: Features 0x1fef6, Bugs 0x40, Flags 0x20485560
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: not probed (disabled)
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xd0000-0xd5fff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1666733799 Hz quality 800
Timecounters tick every 10.000 msec
Linux ELF exec handler installed
lo0: bpf attached
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0%
ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
ata0-master: setting PIO4 on VIA 82C686B chip
acd0: <CD-W516EB/1.0A> CDRW drive at ata0 as master
acd0: read 6890KB/s (6890KB/s) write 2755KB/s (2755KB/s), 1456KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-R 120mm data disc
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(probe0:ahc0:0:0:0): Retrying Command
(ahc0:A:0:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:0:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 0 using 16bit transfers
ahc0: target 0 synchronous at 80.0MHz DT, offset = 0x3f
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <SEAGATE ST336706LW 0109> Fixed Direct Access SCSI-3 device
pass0: Serial Number 3FD0RQY700007234TV4J
pass0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
GEOM: create disk da0 dp=0xc2e70850
GEOM: new disk da0
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST336706LW 0109> Fixed Direct Access SCSI-3 device
da0: Serial Number 3FD0RQY700007234TV4J
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 35003MB (71687370 512 byte sectors: 255H 63S/T 4462C)
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:71681967
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 32256 length 36701167104 end 36701199359
GEOM: Configure da0s1a, start 0 length 268435456 end 268435455
GEOM: Configure da0s1b, start 268435456 length 536870912 end 805306367
GEOM: Configure da0s1c, start 0 length 36701167104 end 36701167103
GEOM: Configure da0s1d, start 805306368 length 268435456 end 1073741823
GEOM: Configure da0s1e, start 1073741824 length 35627425280 end 36701167103
Mounting root from ufs:/dev/da0s1a
start_init: trying /sbin/init
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
- Previous message: Tinderbox: "[current tinderbox] failure on sparc64/sparc64"
- Next in thread: Joe Marcus Clarke: "Re: The reboot doesn't work anymore in today -CURRENT.."
- Reply: Joe Marcus Clarke: "Re: The reboot doesn't work anymore in today -CURRENT.."
- Reply: UDSD387: ""Me too" re: The reboot doesn't work anymore in today -CURRENT.."
- Reply: pseniura_at_techie.com: ""Me too" addendum re: The reboot doesn't work anymore in today -CURRENT.."
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
