Re: System still hangs with "ata1-master: TIMEOUT - SETFEATURES SET TRANSFER MODE"

From: Panagiotis Astithas (past_at_noc.ntua.gr)
Date: 01/27/04

  • Next message: Jamie Bowden: "Re: Project Evil: The Evil Continues" 
    Date: Tue, 27 Jan 2004 16:17:27 +0200
To: Lefteris Chatzibarbas <lefcha@hellug.gr>

    Lefteris Chatzibarbas wrote:
    > Hello,
    >
    > Devices are:
    >
    > ad0: <WDC WD800JB-00ETA0/77.07W77> ATA-6 disk at ata0-master
    > acd0: <DV-516E/3.04> DVDROM drive at ata1 as master
    > acd1: <CD-W524E/1.0A> CDRW drive at ata1 as slave
    >
    > Verbose boot of a good kernel:
    >
    > http://members.hellug.gr/lefcha/dmesg.out
    >
    > System still hangs during boot with the message:
    >
    > ata1-master: TIMEOUT - SETFEATURES SET TRANSFER MODE retrying (0 retries left)
    >
    > ... and verbose boot:
    >
    > ata1: reiniting channel ..
    > ata1: reset tp1 mask=03 ostat0=50 ostat1=50
    > ata1-master: stat=0x10 err=0x01 lib=0x14 msb=0xeb
    > ata1-slave: stat=0x10 err=0x01 lib=0x14 msb=0xeb
    > ata1: reset tp2 mask=03 stat0=10 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
    > ata1: resetting done ..
    > ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
    > ata1: reiniting channel ..
    > ata1: reset tp1 mask=03 ostat0=50 ostat1=50
    > ata1-master: stat=0x10 err=0x01 lib=0x14 msb=0xeb
    > ata1-slave: stat=0x10 err=0x01 lib=0x14 msb=0xeb
    > ata1: reset tp2 mask=03 stat0=10 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
    > ata1: resetting done ..
    > ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
    >
    > Soren Schmidt's commit 2004/01/19 07:20:00 PST:
    >
    > 1.202 +2 -1 src/sys/dev/ata/ata-all.c
    > 1.71 +1 -1 src/sys/dev/ata/ata-all.h
    > 1.17 +23 -21 src/sys/dev/ata/ata-queue.c
    > 1.161 +1 -1 src/sys/dev/ata/atapi-cd.c
    >
    > ... or:
    >
    > http://lists.freebsd.org/pipermail/cvs-src/2004-January/016880.html
    >
    > ... didn't correct the problem.
    >
    > Thanks

    "Me too".
    Same controller, same hard disk, only one device on the second channel:
    acd0: DVDROM <DVD-ROM DDU1621> at ata1-master UDMA33
    I used 5.2-RELEASE and the -current snapshot form 24/1. The former
    freezes after the "TIMEOUT" message, the latter just locks up solid. The
    machine runs happily a -current from last October though.

    Cheers, 

    -- 
Panagiotis Astithas
Electrical & Computer Engineer, PhD
Network Management Center
National Technical University of Athens, Greece
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
  • Next message: Jamie Bowden: "Re: Project Evil: The Evil Continues"

    Relevant Pages

    • RE: Latest kernel hanging after amr (dell 1550)
      ... >> Grabbed a new CVS snapshot and kernel still hangs at same place. ... Alright...here's a verbose boot on the SMP 1550, ...
      (freebsd-current)
    • Re: Cant install any version of FreeBSD 5.x
      ... Verbose boot is best. ... support for DDB (see the developers' handbook) and break to DDB at ... the point where it hangs, ... This is explained in the developers' handbook. ...
      (comp.unix.bsd.freebsd.misc)
    • Re: ATAng no good for me
      ... > No, using latest sources, with or without atapicam, does ... It still hangs. ... > Full verbose boot log at: ... To unsubscribe, ...
      (freebsd-current)
    • Re: ATA still broken
      ... > Lefteris Chatzibarbas wrote: ... > That doesn't help me much at all, it was broken before at probe but ... > that was newer noticed since it worked afterwards. ...
      (freebsd-current)
    • Re: No root filesystem
      ... I also observe that k8temp doesn't attach. ... for the old kernel and one for the new kernel. ... bloat the verbose boot output beyond the limit that i could still get ...
      (freebsd-current)