Re: 5.2.1 Vinum/Firewire/Crash under load?
From: Sean Hafeez (sahafeez_at_zaphodb.org)
Date: 04/30/04
- Previous message: Sean Hafeez: "5.2.1 Vinum/Firewire/Crash under load?"
- In reply to: Sean Hafeez: "5.2.1 Vinum/Firewire/Crash under load?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Fri, 30 Apr 2004 13:54:28 -0700
ok. so i booted the system without the fw drives on. and things worked
fine. i was going to kill the vinum and newfs each drive and try to
move data to them. the system crashed just the same. i think the issue
is with the fw code.
-sean
On Apr 30, 2004, at 1:38 PM, Sean Hafeez wrote:
> Just built a new system.
>
> AMD2000+, 512MB RAM, 2 NIC (re0, vr0), Firewire with 4 drives.
>
>
> fwohci0: <VIA VT6306> port 0xc800-0xc87f mem 0xe0061000-0xe00617ff irq
> 11 at device 12.0 on pci0
> fwohci0: OHCI version 1.0 (ROM=1)
> fwohci0: No. of Isochronous channel is 8.
> fwohci0: EUI64 00:11:06:00:00:00:ab:27
> fwohci0: Phy 1394a available S400, 3 ports.
> fwohci0: Link S100, max_rec 2 bytes.
> fwohci0: max_rec 2 -> 2048
> firewire0: <IEEE1394(FireWire) bus> on fwohci0
> fwe0: <Ethernet over FireWire> on firewire0
> if_fwe0: Fake Ethernet address: 02:11:06:00:ab:27
> sbp0: <SBP-2/SCSI over FireWire> on firewire0
> fwohci0: Initiate bus reset
> fwohci0: BUS reset
> fwohci0: node_id=0xc800ffc2, gen=1, CYCLEMASTER mode
> firewire0: 3 nodes, maxhop <= 2, cable IRM = 2 (me)
> firewire0: bus manager 2 (me)
>
> ....
>
> da0 at sbp0 bus 0 target 0 lun 0
> da0: <Oxford S OXFORD IDE Devic 0138> Fixed Simplified Direct Access
> SCSI-4 device
> da0: 50.000MB/s transfers, Tagged Queueing Enabled
> da0: 156334MB (320173056 512 byte sectors: 255H 63S/T 19929C)
> da1 at sbp0 bus 0 target 0 lun 1
> da1: <Oxford S OXFORD IDE Devic 0138> Fixed Simplified Direct Access
> SCSI-4 device
> da1: 50.000MB/s transfers, Tagged Queueing Enabled
> da1: 156334MB (320173056 512 byte sectors: 255H 63S/T 19929C)
> da2 at sbp0 bus 0 target 1 lun 0
> da2: <Oxford S OXFORD IDE Devic 0138> Fixed Simplified Direct Access
> SCSI-4 device
> da2: 50.000MB/s transfers, Tagged Queueing Enabled
> da2: 156334MB (320173056 512 byte sectors: 255H 63S/T 19929C)
> da3 at sbp0 bus 0 target 1 lun 1
> da3: <Oxford S OXFORD IDE Devic 0138> Fixed Simplified Direct Access
> SCSI-4 device
> da3: 50.000MB/s transfers, Tagged Queueing Enabled
> da3: 156334MB (320173056 512 byte sectors: 255H 63S/T 19929C)
>
>
> I setup Vinum as RAID5. I did a full INIT of all the drives.
>
> After that was done I newfs'd it and the system crash - rebooted - no
> logs.
>
> Hum. I had messed with the kernel trying to get RAIDFRAME working 1st
> so I nuked the system and started over with GENERIC.
>
> OK, set everything up again. newfs works. Mount the drive. Everything
> seems OK.
>
> make install samaba .... and start copying over 80gb of files. Bam!
> Reboots. No Logs.
>
> Hum. OK. Just thru hoops - tried 5.1 and 5.2 - same issues.
>
> Tried Win2K server - maid a RAID5 with the Windows tools. Copied
> everything over fine - been up and running for hours..
>
> Anyone point me to want to look at or what files I could post?
>
> Thanks,
> Sean
>
> _______________________________________________
> freebsd-current@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to
> "freebsd-current-unsubscribe@freebsd.org"
>
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
- Previous message: Sean Hafeez: "5.2.1 Vinum/Firewire/Crash under load?"
- In reply to: Sean Hafeez: "5.2.1 Vinum/Firewire/Crash under load?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
