Re: device pcic and card
From: Ian FREISLICH (if_at_hetzner.co.za)
Date: 03/18/05
- Previous message: Bjoern A. Zeeb: "Re: kernel page fault panic in yesterday's current ( nfs_nget -> vfs_hash_insert -> bcmp )"
- Maybe in reply to: Maksim Yevmenkin: "Re: device pcic and card"
- Next in thread: Warner Losh: "Re: device pcic and card"
- Reply: Warner Losh: "Re: device pcic and card"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
To: "M. Warner Losh" <imp@bsdimp.com> Date: Fri, 18 Mar 2005 12:21:11 +0200
"M. Warner Losh" wrote:
> In message: <E1DBRvf-000M6z-00@hetzner.co.za>
> Ian FREISLICH <if@hetzner.co.za> writes:
> : I cannot migrate to cbb and pccard: my Vadem 468 is not supported.
> : I know the hardware is old. Are there any plans to support this
> : or should I just give up and run 4.x on this laptop (it will be
> : quite inconvenient to downgrade)?
>
> You can run 5.x on this machine.
>
> However, it is my belief that it is supported with the new cbb_isa
> attachment.
Hmm, I got the part number wrong, it's a vadem 469. How do I get
cbb_isa to attach?
This is the output of ident /boot/kernel/cbb.ko
/boot/kernel/cbb.ko:
$FreeBSD: src/sys/dev/pccbb/pccbb.c,v 1.121 2005/01/13 19:05:25 imp Exp $
$FreeBSD: src/sys/dev/pccbb/pccbb_isa.c,v 1.4 2005/01/11 05:33:18 imp Exp $
$FreeBSD: src/sys/dev/pccbb/pccbb_pci.c,v 1.7 2005/03/05 18:10:49 imp Exp $
Attached are two verbose boot logs. The first is my working kernel
from 16 Nov 2004. The second is 17 Mar 2005 with:
device cbb
device pccard
device cardbus
This extra line appears in the new kernel's output. Is this perhaps
what was detected as in the older kernel as pcic0?
unknown: <PNP0c01> can't assign resources (memory)
Is there anything else that I should be doing that I'm not?
Ian
--
Ian Freislich
SMAP type=01 base=0000000000000000 len=00000000000a0000
SMAP type=01 base=0000000000100000 len=0000000001f00000
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-CURRENT #0: Tue Nov 16 12:52:12 SAST 2004
ianf@laptoy.freislich.nom.za:/usr/obj/usr/src/sys/LAPTOY
Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc06d6000.
Preloaded elf module "/boot/kernel.old/if_ed.ko" at 0xc06d610c.
Preloaded elf module "/boot/kernel.old/miibus.ko" at 0xc06d61bc.
Preloaded elf module "/boot/kernel.old/snd_ess.ko" at 0xc06d626c.
Preloaded elf module "/boot/kernel.old/sound.ko" at 0xc06d631c.
Preloaded elf module "/boot/kernel.old/snd_sbc.ko" at 0xc06d63cc.
Preloaded elf module "/boot/kernel.old/random.ko" at 0xc06d647c.
Preloaded elf module "/boot/kernel.old/io.ko" at 0xc06d652c.
Preloaded elf module "/boot/kernel.old/mem.ko" at 0xc06d65d8.
Calibrating clock(s) ... i8254 clock: 1193213 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 133637317 Hz
CPU: Pentium/P54C (133.64-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x52c Stepping = 12
Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory = 33554432 (32 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009ffff, 651264 bytes (159 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000826000 - 0x0000000001f3ffff, 24223744 bytes (5914 pages)
avail memory = 27717632 (26 MB)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xbe4e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4 Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
Intel Pentium detected, installing workaround for F00F bug
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
io: <I/O>
mem: <memory>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=00011066)
pcibios: BIOS version 2.10
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.1, connected at v1.1
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1066, dev=0x0001, revid=0x04
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0xa400, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1066, dev=0x8002, revid=0x00
bus=0, slot=6, func=0
class=06-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x000f, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base 30000000, size 21, enabled
found-> vendor=0x10c8, dev=0x0001, revid=0x01
bus=0, slot=7, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
map[20]: type 4, range 32, base 0000fe00, size 4, enabled
found-> vendor=0x1095, dev=0x0643, revid=0x00
bus=0, slot=8, func=0
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=14
isab0: <PCI-ISA bridge> at device 6.0 on pci0
isa0: <ISA bus> on isab0
pci0: <display, VGA> at device 7.0 (no driver attached)
atapci0: <GENERIC ATA controller> port 0xfe00-0xfe0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 14 at device 8.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfe00
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: [MPSAFE]
cpu0 on motherboard
pnpbios: 16 devices, largest 468 bytes
PNP0a03: adding io range 0xcf8-0xcf8, size=0x1, align=0x1
PNP0a03: adding io range 0xcfa-0xcfa, size=0x1, align=0x1
pnpbios: handle 0 device ID PNP0a03 (030ad041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x1ffffff, size=0x1f00000
PNP0c01: adding fixed memory32 range 0xf0000-0xfffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding io range 0x180-0x180, size=0x1, align=0x1
pnpbios: handle 1 device ID PNP0c01 (010cd041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x5f, size=0x20, align=0x1
pnpbios: handle 3 device ID PNP0100 (0001d041)
PNP0200: adding io range 0x80-0x9f, size=0x20, align=0x1
PNP0200: adding io range 0-0x1f, size=0x20, align=0x1
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
PNP0200: adding dma mask 0x10
pnpbios: handle 4 device ID PNP0200 (0002d041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
pnpbios: handle 5 device ID PNP0303 (0303d041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 6 device ID PNP0f13 (130fd041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 7 device ID PNP0800 (0008d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x7f, size=0x10, align=0x1
pnpbios: handle 8 device ID PNP0b00 (000bd041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
pnpbios: handle 9 device ID PNP0c04 (040cd041)
PNP0e00: adding io range 0x3e0-0x3e1, size=0x2, align=0x1
pnpbios: handle 10 device ID PNP0e00 (000ed041)
ESS0106: adding fixed io range 0x230-0x23f, size=0x10, align=0x1
ESS0106: adding fixed io range 0x388-0x38b, size=0x4, align=0x1
ESS0106: adding fixed io range 0x330-0x331, size=0x2, align=0x1
ESS0106: adding irq mask 0x20
ESS0106: adding irq mask 0x200
ESS0106: adding dma mask 0x1
ESS0106: adding dma mask 0x8
pnpbios: handle 11 device ID ESS0106 (06017316)
PNP0501: adding irq mask 0x10
PNP0501: adding fixed io range 0x3f8-0x3ff, size=0x8, align=0x1
pnpbios: handle 12 device ID PNP0501 (0105d041)
PNP0510: adding irq mask 0x8
PNP0510: adding fixed io range 0x2f8-0x2ff, size=0x8, align=0x1
pnpbios: handle 13 device ID PNP0510 (1005d041)
PNP0401: adding irq mask 0x80
PNP0401: adding fixed io range 0x378-0x37f, size=0x8, align=0x1
pnpbios: handle 14 device ID PNP0401 (0104d041)
PNP0700: adding irq mask 0x40
PNP0700: adding fixed io range 0x3f2-0x3f5, size=0x4, align=0x1
PNP0700: adding fixed io range 0x3f7-0x3f7, size=0x1, align=0x1
PNP0700: adding dma mask 0x4
pnpbios: handle 15 device ID PNP0700 (0007d041)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xc0000-0xcbfff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0001
psm0: strange result for test aux port (1).
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 05 02 c8
psm: status 05 02 c8
psm: status 05 02 c8
psm: data 08 00 00
psm: status 10 00 64
psm: status 00 02 64
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ic_type 90 part_id 73
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0: <Vadem 469> at port 0x3e0 iomem 0xd0000 on isa0
pcic0: Polling mode
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pccard1: <PC Card 16-bit bus (classic)> on pcic0
pcic1: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0f13> at irq 12 on isa0
speaker0: <PC speaker> at port 0x61 on isa0
unknown: <PNP0e00> failed to probe at port 0x3e1-0x3e2 on isa0
sbc0: <ESS ES1888 (Dell OEM)> at port 0x330-0x331,0x388-0x38b,0x230-0x23f irq 9,5 drq 3,0 on isa0
sbc0: [GIANT-LOCKED]
pcm0: <ESS 18xx DSP> on sbc0
pcm0: ESS5959 detected
pcm0: [GIANT-LOCKED]
pcm0: sndbuf_setmap ff4000, 1000; 0xc43d0000 -> ff4000
pcm0: sndbuf_setmap ff3000, 1000; 0xc43d1000 -> ff3000
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0510> can't assign resources (port)
unknown: <PNP0510> at port 0x2f8-0x2ff on isa0
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0401> at port 0x378-0x37f on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
Device configuration finished.
TSC timecounter disabled: APM enabled.
Timecounter "TSC" frequency 133637317 Hz quality -1000
Timecounters tick every 1.000 msec
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
pcic0: Power: Vcc=0 Vpp=0
pcic0: Power applied
Power complete.
pcic0: Power: Vcc=-1 Vpp=-1
pcic0: Couldn't autodetect voltage, assuming 5.0V
pcic0: Power applied
pcic0: Output enabled
pcic0: Settling complete
Power complete.
pccard: card inserted, slot 1
pcic0: reset 1 int is 0 stat is dd
ad0: <FUJITSU MHD2032AT/1812> ATA-3 disk at ata0-master
ad0: 3102MB (6354432 sectors), 6304 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, PIO4
GEOM: new disk ad0
pcic0: reset 2 int is 60 stat is dd
Mounting root from ufs:/dev/ad0s1a
SMAP type=01 base=0000000000000000 len=00000000000a0000
SMAP type=01 base=0000000000100000 len=0000000001f00000
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-CURRENT #3: Thu Mar 17 10:53:36 SAST 2005
ianf@laptoy.freislich.nom.za:/usr/obj/usr/src/sys/LAPTOY
Preloaded elf kernel "/boot/kernel/kernel" at 0xc06ed000.
Preloaded elf module "/boot/kernel/if_ed.ko" at 0xc06ed108.
Preloaded elf module "/boot/kernel/miibus.ko" at 0xc06ed1b4.
Preloaded elf module "/boot/kernel/snd_ess.ko" at 0xc06ed260.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc06ed30c.
Preloaded elf module "/boot/kernel/snd_sbc.ko" at 0xc06ed3b8.
Preloaded elf module "/boot/kernel/random.ko" at 0xc06ed464.
Preloaded elf module "/boot/kernel/io.ko" at 0xc06ed510.
Preloaded elf module "/boot/kernel/mem.ko" at 0xc06ed5b8.
Calibrating clock(s) ... i8254 clock: 1193213 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 133637416 Hz
CPU: Pentium/P54C (133.64-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x52c Stepping = 12
Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory = 33554432 (32 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009ffff, 651264 bytes (159 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000825000 - 0x0000000001f3ffff, 24227840 bytes (5915 pages)
avail memory = 27713536 (26 MB)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xbe4e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4 Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
Intel Pentium detected, installing workaround for F00F bug
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
io: <I/O>
mem: <memory>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=00011066)
pcibios: BIOS version 2.10
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.1, connected at v1.1
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1066, dev=0x0001, revid=0x04
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0xa400, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1066, dev=0x8002, revid=0x00
bus=0, slot=6, func=0
class=06-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x000f, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base 30000000, size 21, enabled
found-> vendor=0x10c8, dev=0x0001, revid=0x01
bus=0, slot=7, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
map[20]: type 4, range 32, base 0000fe00, size 4, enabled
found-> vendor=0x1095, dev=0x0643, revid=0x00
bus=0, slot=8, func=0
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=14
isab0: <PCI-ISA bridge> at device 6.0 on pci0
isa0: <ISA bus> on isab0
pci0: <display, VGA> at device 7.0 (no driver attached)
atapci0: <GENERIC ATA controller> port 0xfe00-0xfe0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 14 at device 8.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfe00
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: [MPSAFE]
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
pnpbios: 16 devices, largest 468 bytes
PNP0a03: adding io range 0xcf8-0xcf8, size=0x1, align=0x1
PNP0a03: adding io range 0xcfa-0xcfa, size=0x1, align=0x1
pnpbios: handle 0 device ID PNP0a03 (030ad041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x1ffffff, size=0x1f00000
PNP0c01: adding fixed memory32 range 0xf0000-0xfffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding io range 0x180-0x180, size=0x1, align=0x1
pnpbios: handle 1 device ID PNP0c01 (010cd041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x5f, size=0x20, align=0x1
pnpbios: handle 3 device ID PNP0100 (0001d041)
PNP0200: adding io range 0x80-0x9f, size=0x20, align=0x1
PNP0200: adding io range 0-0x1f, size=0x20, align=0x1
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
PNP0200: adding dma mask 0x10
pnpbios: handle 4 device ID PNP0200 (0002d041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
pnpbios: handle 5 device ID PNP0303 (0303d041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 6 device ID PNP0f13 (130fd041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 7 device ID PNP0800 (0008d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x7f, size=0x10, align=0x1
pnpbios: handle 8 device ID PNP0b00 (000bd041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
pnpbios: handle 9 device ID PNP0c04 (040cd041)
PNP0e00: adding io range 0x3e0-0x3e1, size=0x2, align=0x1
pnpbios: handle 10 device ID PNP0e00 (000ed041)
ESS0106: adding fixed io range 0x230-0x23f, size=0x10, align=0x1
ESS0106: adding fixed io range 0x388-0x38b, size=0x4, align=0x1
ESS0106: adding fixed io range 0x330-0x331, size=0x2, align=0x1
ESS0106: adding irq mask 0x20
ESS0106: adding irq mask 0x200
ESS0106: adding dma mask 0x1
ESS0106: adding dma mask 0x8
pnpbios: handle 11 device ID ESS0106 (06017316)
PNP0501: adding irq mask 0x10
PNP0501: adding fixed io range 0x3f8-0x3ff, size=0x8, align=0x1
pnpbios: handle 12 device ID PNP0501 (0105d041)
PNP0510: adding irq mask 0x8
PNP0510: adding fixed io range 0x2f8-0x2ff, size=0x8, align=0x1
pnpbios: handle 13 device ID PNP0510 (1005d041)
PNP0401: adding irq mask 0x80
PNP0401: adding fixed io range 0x378-0x37f, size=0x8, align=0x1
pnpbios: handle 14 device ID PNP0401 (0104d041)
PNP0700: adding irq mask 0x40
PNP0700: adding fixed io range 0x3f2-0x3f5, size=0x4, align=0x1
PNP0700: adding fixed io range 0x3f7-0x3f7, size=0x1, align=0x1
PNP0700: adding dma mask 0x4
pnpbios: handle 15 device ID PNP0700 (0007d041)
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xc0000-0xcbfff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0001
psm0: strange result for test aux port (1).
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 05 02 c8
psm: status 05 02 c8
psm: status 05 02 c8
psm: data 08 00 00
psm: status 10 00 64
psm: status 00 02 64
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ic_type 90 part_id 73
fdc0: <Enhanced floppy controller> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0xf0000-0xfffff,0x100000-0x1ffffff,0-0x9ffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0f13> at irq 12 on isa0
speaker0: <PC speaker> at port 0x61 on isa0
unknown: <PNP0e00> failed to probe at port 0x3e0-0x3e1 on isa0
sbc0: <ESS ES1888 (Dell OEM)> at port 0x330-0x331,0x388-0x38b,0x230-0x23f irq 9,5 drq 3,0 on isa0
sbc0: [GIANT-LOCKED]
pcm0: <ESS 18xx DSP> on sbc0
pcm0: ESS5959 detected
pcm0: [GIANT-LOCKED]
pcm0: sndbuf_setmap ff4000, 1000; 0xc4682000 -> ff4000
pcm0: sndbuf_setmap ff3000, 1000; 0xc4683000 -> ff3000
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0510> can't assign resources (port)
unknown: <PNP0510> at port 0x2f8-0x2ff on isa0
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0401> at port 0x378-0x37f on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
Device configuration finished.
TSC timecounter disabled: APM enabled.
Timecounter "TSC" frequency 133637416 Hz quality -1000
Timecounters tick every 1.000 msec
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
ad0: <FUJITSU MHD2032AT/1812> ATA-3 disk at ata0-master
ad0: 3102MB (6354432 sectors), 6304 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, PIO4
GEOM: new disk ad0
Trying to mount root from ufs:/dev/ad0s1a
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
- Previous message: Bjoern A. Zeeb: "Re: kernel page fault panic in yesterday's current ( nfs_nget -> vfs_hash_insert -> bcmp )"
- Maybe in reply to: Maksim Yevmenkin: "Re: device pcic and card"
- Next in thread: Warner Losh: "Re: device pcic and card"
- Reply: Warner Losh: "Re: device pcic and card"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
