Re: chelsio driver and Myricom driver
- From: "Kip Macy" <kip.macy@xxxxxxxxx>
- Date: Tue, 17 Jul 2007 21:27:40 -0700
You need to use the module in order to update the firmware. The
firmware will be automatically be updated when you up an interface on
the card.
-Kip
On 7/17/07, Mike Tancsa <mike@xxxxxxxxxx> wrote:
Hi,_______________________________________________
I am trying to run a recent current with the Chelsio 10GigE card
below and it tries to load but has the following complaint.
cxgbc0: <Chelsio T310 RNIC, 1 port> mem
0xe0201000-0xe0201fff,0xe0800000-0xe0ffffff,0xe0200000-0xe0200fff irq
16 at device 0.0 on pci10
cxgbc0: found wrong FW version (4.0), driver needs version 4.5
cxgbc0: firmware needs to be updated to version 4.5.0
cxgbc0: found wrong TP version (0.0), driver needs version 1.1
cxgbc0: SRAM needs to be updated to version b-1.1.0
cxgb0: <Port 0 10GBASE-CX4> on cxgbc0
cxgb0: Ethernet address: 00:07:43:04:01:2c
Where do I get the firmware from ? The website only has 4.3 ? Also,
how do I update the SRAM. Sorry if these are obvious questions, but
I am new to CURRENT with such drivers. I have the driver compiled
into the kernel
With the Myricom, it seems to work, but it doesnt detect the cx4
media type for some reason.
# ifconfig mxge0
mxge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000
options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4>
ether 00:60:dd:47:c6:c4
inet 192.168.10.3 netmask 0xffffff00 broadcast 192.168.10.255
media: <unknown type> (autoselect <full-duplex>)
status: active
The port is up and I can ping across it so it is working.
TenGigabitEthernet2/3 is up, line protocol is up (connected)
Hardware is C6k 10000Mb 802.3, address is 0018.bab0.2036 (bia
0018.bab0.2036)
Description: leopard3 mxge0
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 10Gb/s
input flow-control is off, output flow-control is on
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:55, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
8 packets input, 588 bytes, 0 no buffer
Received 5 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
403 packets output, 30468 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
---Mike
--------------------------------------------------------------------
Mike Tancsa, tel +1 519 651 3400
Sentex Communications, mike@xxxxxxxxxx
Providing Internet since 1994 www.sentex.net
Cambridge, Ontario Canada www.sentex.net/mike
_______________________________________________
freebsd-current@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@xxxxxxxxxxx"
freebsd-current@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@xxxxxxxxxxx"
- References:
- chelsio driver and Myricom driver
- From: Mike Tancsa
- chelsio driver and Myricom driver
- Prev by Date: Re: Slow networkperformance in current?
- Next by Date: Re: chelsio driver and Myricom driver
- Previous by thread: chelsio driver and Myricom driver
- Next by thread: Re: chelsio driver and Myricom driver
- Index(es):
Relevant Pages
|
