Re: pccard0: Card has no functions! (solved)

On 2007-08-17 00:53 +0200, Marian Cerny wrote:
I have Nokia Card Phone 2.0 (on a supported HW list) in a PCMCIA to PCI
adapter. I have used this combination some time ago (2-3 years) and it worked
without any problems. I don't remember what FreeBSD version I used that time.

I tried to get it working under FreeBSD 6.2R today but was not
successful. I can see those messages after boot:

Status is 0x30000410
cbb0: card inserted: event=0x00000000, state=30000410
pccard0: chip_socket_enable
cbb_pcic_socket_enable:
cbb0: cbb_power: 5V
pccard0: read_cis
cis mem map 0xe7286000 (resource: 0xfe310000)
pccard0: CIS tuple chain:
CISTPL_END
ff
cis mem map e7286000
CISTPL_LINKTARGET expected, code ff observed
pccard0: check_cis_quirks
pccard0: Card has no functions!
cbb0: PC Card card activation failed

The problem was in the PCI to PCMCIA adapter. It was not able to read
"CIS tuple chain" of any PCMCIA card. I have bought a new adapter, with
a Ricoh R5C485 chip (the old one had R5C475II) and it works without any
problems. The real problem with the old adapter was not fixed - however
I consider the problem to be solved.

pciconf -lv:
cbb0@pci5:2:0: class=0x060700 card=0x010114ef chip=0x04751180 rev=0x80 hdr=0x02
vendor = 'Ricoh Co Ltd'
device = 'RL5c475 CardBus Controller'
class = bridge
subclass = PCI-CardBus

The new adapter is similar to the old one according to pciconf:

cbb0@pci1:0:0: class=0x060700 card=0x00000000 chip=0x04751180 rev=0x81 hdr=0x02
vendor = 'Ricoh Co Ltd'
device = 'RL5c475 CardBus Controller'
class = bridge
subclass = PCI-CardBus

Marian Cerny
_______________________________________________
freebsd-hackers@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
To unsubscribe, send any mail to "freebsd-hackers-unsubscribe@xxxxxxxxxxx"

Relevant Pages

  • RE: pccard0: Card has no functions! (solved)
    ... pccard0: chip_socket_enable ... cis mem map 0xe7286000 ... PC Card card activation failed ... The problem was in the PCI to PCMCIA adapter. ...
    (freebsd-hackers)
  • 5.2-current: devfs and pcmcia configuration question
    ... I've got problems to setup my notebook that my CF Adapter is readable through ... a auto mounted device by any ordinary user. ... In dmesg the cardbus adapter shows up as: ... pccard0: ...
    (freebsd-current)
  • Re: pccard0: Card has no functions!
    ... pcib5: pccard0 requested memory range 0xfe300000-0xfeafffff: good ... cis mem map 0xe6e2c000 ... PC Card card activation failed ... device = 'RL5c475 CardBus Controller' ...
    (freebsd-hackers)
  • Re: HDdriver and CF card drive problem
    ... I don't think it's the cable, but the adapter is indeed acting ... The card reader uses a 25 pin connector, so to connect it to the 50 ... The other end of the cable from the ICD Link II goes to the Mega STe ... plan is to install some sort of IDE interface and use a Compact Flash ...
    (comp.sys.atari.st)
  • Re: PCMCIA Adapter for SD cards: Which one, and how?
    ... With a SD to CF adapter, I can now read a card faster than via USB 1.1, ... Going the route SD to CF adapter in a CF to PCMCIA adapter did not work ... Bus 1: ...
    (comp.os.os2.setup.storage)