FBSD 5.1 install problem on a DL380

From: W.D.McKinney (dee_at_akwireless.net)
Date: 01/26/04

  • Next message: Sten Daniel Sørsdal: "RE: BGP4 using FreeBSD" 
    To: freebsd-isp@freebsd.org
Date: Sun, 25 Jan 2004 14:24:39 -0900

    I am trying to get 5.x to install on a used Compaq DL380.
    4.9 works OK, but we'd like to be using 5.1.

    It locks up with the install CD of 5.1 when it hits the video card.

    boot info (under 4.9) is:

    Copyright (c) 1992-2003 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
            The Regents of the University of California. All rights
    reserved.
    FreeBSD 4.9-RELEASE #0: Wed Jan 21 23:37:09 AKST 2004
        deem@burger.wdm-lan:/usr/src/sys/compile/BURGER-KERNEL
    Timecounter "i8254" frequency 1193182 Hz
    CPU: Intel Pentium III (863.94-MHz 686-class CPU)
      Origin = "GenuineIntel" Id = 0x683 Stepping = 3
     
    Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
    real memory = 536854528 (524272K bytes)
    avail memory = 518209536 (506064K bytes)
    Changing APIC ID for IO APIC #0 from 0 to 8 on chip
    Programming 35 pins in IOAPIC #0
    IOAPIC #0 intpin 2 -> irq 0
    FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs
     cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
     cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
     io0 (APIC): apic id: 8, version: 0x00220011, at 0xfec00000
    Preloaded elf kernel "kernel" at 0xc040c000.
    Pentium Pro MTRR support enabled
    md0: Malloc disk
    npx0: <math processor> on motherboard
    npx0: INT 16 interface
    pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
    IOAPIC #0 intpin 19 -> irq 2
    IOAPIC #0 intpin 17 -> irq 5
    pci0: <PCI bus> on pcib0
    ida0: <Compaq Integrated Array controller> port 0x2000-0x20ff mem
    0xc5000000-0xc5ffffff,0xc6000000-0xc6ffffff irq 2 at device 1.0 on pci0
    ida0: drives=1 firm_rev=1.42
    idad0: <Compaq Logical Drive> on ida0
    idad0: 17343MB (35520480 sectors), blocksize=512
    fxp0: <Intel 82559 Pro/100 Ethernet> port 0x2400-0x243f mem
    0xc4e00000-0xc4efffff,0xc4fff000-0xc4ffffff irq 5 at device 2.0 on pci0
    fxp0: Ethernet address 00:50:8b:dc:cb:91
    inphy0: <i82555 10/100 media interface> on miibus0
    inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    pci0: <ATI Mach64-GV graphics accelerator> at 3.0
    pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 4.0
    isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
    isa0: <ISA bus> on isab0
    atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x2c00-0x2c0f at
    device 15.1 on pci0
    ata0: at 0x1f0 irq 14 on atapci0
    ata1: at 0x170 irq 15 on atapci0
    pcib3: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
    pci3: <PCI bus> on pcib3
    eisa0: <EISA bus> on motherboard
    mainboard0: <CPQ0692 (System Board)> on eisa0 slot 0
    orm0: <Option ROMs> at iomem
    0xc0000-0xc7fff,0xc8000-0xcbfff,0xe8000-0xedfff,0xee000-0xeffff on isa0
    pmtimer0 on isa0
    fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
    isa0
    fdc0: FIFO enabled, 8 bytes threshold
    fd0: <1440-KB 3.5" drive> on fdc0 drive 0
    atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
    atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
    kbd0 at atkbd0
    vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
    isa0
    sc0: <System console> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
    sio0: type 16550A
    sio1 at port 0x2f8-0x2ff irq 3 on isa0
    sio1: type 16550A
    ppc0: cannot reserve I/O port range
    APIC_IO: Testing 8254 interrupt delivery
    APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0
    intpin 2
    APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0
    SMP: AP CPU #1 Launched!
    acd0: CDROM <Compaq CRN-8241B> at ata0-master PIO4

    Any ideas on boot parameters to get 5.1 to install ?

    Thanks,
    Dee

    _______________________________________________
    freebsd-isp@freebsd.org mailing list
    http://lists.freebsd.org/mailman/listinfo/freebsd-isp
    To unsubscribe, send any mail to "freebsd-isp-unsubscribe@freebsd.org"

  • Next message: Sten Daniel Sørsdal: "RE: BGP4 using FreeBSD"

    Relevant Pages

    • Re: 5.2 on DELL m/cs
      ... install, kernel panics at first boot after installation. ... pci0: <PCI bus> on pcib0 ... 0xc0000-0xc7fff,0xc8000-0xcdfff,0xce000-0xcffff on isa0 ... configured irq 4 not in bitmap of probed irqs 0 ...
      (freebsd-current)
    • Re: KB898458???
      ... it to them to install Linux. ... So it was a system reset you were doing from recovery discs, ... but use the key that came with the Compaq. ... everything except one cd-rom and my wireless lan card. ...
      (microsoft.public.windowsxp.general)
    • Re: New XP Pro wont boot up
      ... I'm assuming that the folder on the hdd you used to install windows xp was ... compaq in case you had to reinstall xp. ... MB Memory: First boot device ...
      (microsoft.public.windowsxp.basics)
    • Re: Im going crazy-please HELP!
      ... been told that's all I could do if I couldn't start windows or start ... the Compaq Quick Restore CD that I've always used to revert the PC back ... message telling me to contact Compaq. ... an install on my rig. ...
      (microsoft.public.windowsxp.help_and_support)
    • Re: KB898458???
      ... I didn't know I could load winxp from one of my disk but use the numbers off ... systems but I thought you can only install WinXp on one system at a time? ... the PC has changed and no longer match the recovery discs settings. ... but use the key that came with the Compaq. ...
      (microsoft.public.windowsxp.general)