Re: Best IDE RAID5 solution for FreeBSD 5.2 ?
From: Dmitry Alyabyev (dimitry_at_al.org.ua)
Date: 03/09/04
- Previous message: Adrian _at_ Connexus: "Re: Best IDE RAID5 solution for FreeBSD 5.2 ?"
- In reply to: Adrian: "Best IDE RAID5 solution for FreeBSD 5.2 ?"
- Next in thread: Adrian _at_ Connexus: "Re: Best IDE RAID5 solution for FreeBSD 5.2 ?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
To: Adrian <adrian-ml@connexus.net.au> Date: Tue, 9 Mar 2004 11:47:10 +0200
hi
almost the same happened to me with Promise RAID card and couple of IDE WDs
(100..120GB).
finally I found that the source of these problems was noise-reduction feature
that is turned on on some IDE disks which were probably designed for
desktops. so I upgraded firmware on all WDs to turn it off - and voila - it
works just fine !
details here:
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=913&p_created=1047068027
hope this helps
-- Dimitry On Tuesday 09 March 2004 03:58, Adrian wrote: > Hi, > > I'm having lots of trouble with 3ware RAID > cards and would like to know what other > people are using.. > > I basically just need to be able to rebuild > degraded arrays remotely (from FreeBSD) as > I don't always have console access to the > machines and can't power-cycle them. > > I have various versions of the 3Ware cards > (mainly 7006). After a while one of the drives > will degrade. If I rebuild it, the same drive > just degrades again soon after. I've replaced > everything from the HD to RAID card, motherboard > and cables - but in the end I have to format the > array and rebuild the machine from scratch but > then after a while it starts doing the same thing.. > This is happening on FreeBSD versions 4.8->5.2 > and across completely different hardware (though > I've only ever used Maxtor IDE drives). > > Any help / suggestions would be appreciated. > > Thanks, > Adrian. > > _______________________________________________ > freebsd-isp@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-isp > To unsubscribe, send any mail to "freebsd-isp-unsubscribe@freebsd.org" _______________________________________________ freebsd-isp@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-isp To unsubscribe, send any mail to "freebsd-isp-unsubscribe@freebsd.org"
- Previous message: Adrian _at_ Connexus: "Re: Best IDE RAID5 solution for FreeBSD 5.2 ?"
- In reply to: Adrian: "Best IDE RAID5 solution for FreeBSD 5.2 ?"
- Next in thread: Adrian _at_ Connexus: "Re: Best IDE RAID5 solution for FreeBSD 5.2 ?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
- Re: Reconnected
... SCSI by far better drives and architechture -- IDE was never ever ...
I tried that with IDE drives, but a failure of the RAID card and ... RAID 5 w SCSI
is usually robust. ... (alt.coffee) - [opensuse] Software IDE RAID versus hardware IDE RAID
... I have an old server with an IDE RAID card in it on ... Install openSUSE
and configure it to use software RAID (two mirrored ... IDE drives for system, ...
(SuSE) - SUMMARY: "hardware level" Cloning IDE-disks for rapid deployment/backup/etc.
... How to make an exact duplicate of an IDE disk from a production ... jumper as
master and attach to "secondary" bus on raid card. ... instead indicate "source" and "target"
drives for cloning. ... (SunManagers) - Re: [SLE] Grub help...need to change from hda to sda
... > I've just installed a 3ware raid card, copied, via dd, an old IDE ... >
drive to a new drive attached to the raid card and now need to know ... > how to change
grub to point to the new drive. ... assuming your partitions look ... (SuSE) - Re: RAID card for IDE on SBS 2003
... I second the 3WARE Closest thing to SCSI you can get using IDE. ... >
SBS2K server and so far it's worked very well. ... >> not be the RAID card driver,
... (microsoft.public.windows.server.sbs)