(no subject)

Can anyone explain to me why I can't get my CARP interfaces up again after changing the spanning-tree version on our customer switch?



We have 2x switches connected to our freebsd routers and a fibre link between the switches.

Customer have a port on each switch going to a third switch and between the 3 switches we have spanning tree running for redundant paths.

I changed the spanning-tree on the customer switch (switch 3) and now my carp interface look like this





carp135: flags=49<UP,LOOPBACK,RUNNING> mtu 1500

inet xxx.xxx.xxx.2 netmask 0xffffff00

carp: MASTER vhid 7 advbase 1 advskew 100



carp135: flags=49<UP,LOOPBACK,RUNNING> mtu 1500

inet xxx.xxx.xxx.2 netmask 0xffffff00

carp: MASTER vhid 7 advbase 1 advskew 0



I tried changing it back to the original spanning-tree but it still doesn't work



$ sysctl net.inet.carp

net.inet.carp.allow: 1

net.inet.carp.preempt: 1

net.inet.carp.log: 1

net.inet.carp.arpbalance: 0

net.inet.carp.suppress_preempt: 0



FreeBSD 6.1-RC1 FreeBSD 6.1-RC1 #0: Wed Apr 26 16:02:45 UTC 2006 root@:/usr/src/sys/i386/compile/CLOWNFISH i386



TeleCityRedbus Sverige
Visit: Mariehällsvägen 36

Address: P.O.Box 20165, 161 02 Bromma, SWEDEN
Phone: +46 8 799 38 00 - Direct: +46 8 799 38 07
Email: tyrone@xxxxxxxxxxx

Internet: http://www.telecity.se <http://www.telecity.se/>

TelecityRedbus is an ISO 9001:2000 & BS7799 certified company
Winner - Best Practice in Network and Infrastructure Security 2005, Aberdeen Group








This e-mail is intended only for the use of the addressees named above and may be confidential.
If you are not an addressee you must not use any information contained in nor copy it nor inform any person other than the addressees of its existence or contents.
If you have received this e-mail in error, please contact the IT department on +44 207 001 0090

_______________________________________________
freebsd-isp@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-isp
To unsubscribe, send any mail to "freebsd-isp-unsubscribe@xxxxxxxxxxx"

Relevant Pages

  • Re: How to remove an interface from spanning tree?
    ... interface FastEthernet X/X ... data units which are the basis for sending and receiving spanning-tree ... You have three switches which are in a loop. ... primary and the secondary switch back but remove spanning-tree from the ...
    (comp.dcom.sys.cisco)
  • Re: strange STP behaviour : stack port in "sh spanning-tree" output
    ... I had to reconfigure "spanning-tree vlan 242-243" on the master to align configs... ... I have three 3750 switch connected in stack ... ... Issuing "sh spanning-tree root port" only for VLAN 242 and 243 you can ...
    (comp.dcom.sys.cisco)
  • Re: Understanding spanning-Tree
    ... I would ask something about spanning-tree, as I'm not expert to it and I'm ... than one VLAN, where every switch partecipate in spanning tree. ... every packet sent by a host in that VLAN must pass through the root bridge ...
    (comp.dcom.sys.cisco)
  • (no subject)
    ... Can anyone explain to me why I can't get my CARP interfaces up again after changing the spanning-tree version on our customer switch? ... Customer have a port on each switch going to a third switch and between the 3 switches we have spanning tree running for redundant paths. ...
    (freebsd-isp)