SCSI disk not available in 5.2.1-RELEASE while 4.10-RELEASE can use it

• Previous message: dvv: "Re: SPARC2"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Date: Thu, 08 Jul 2004 15:40:35 +0200
To: freebsd-questions@freebsd.org

Dear FreeBSD-questions people,

Short desc.:

FreeBSD 5.2.1-RELEASE doesnt see scsi disks, very early still at
bootloader, while FreeBSD 4.10-RELEASE does.

Long:

Hardware being used is a Supermicro 6013P8 with a onboard Adaptec
AIC-7902 with an Adaptec 2015S raid module. The system has two internal
disks being mirrored raid1. An external raid cabinet, a Infortrend
Eonstor A08, is attached as two scsi-3 disk devices. The Adaptec bios
does show the devices everytime we reboot. When 4.10 starts it directly
gives the list of bios exported devices disk A: till D: while 5.2.1
doesnt list B:. We also tried upgrading from 5.2.1-RELEASE to
5.2-CURRENT without luck.

Any help would be greatly appriciated.

--
Leroy van Logchem
### Output of camcontrol devlist -v on FreeBSD 4.10-RELEASE:
localhost# camcontrol devlist -v
scbus0 on asr0 bus 0:
<ADAPTEC RAID-1 3B05>              at scbus0 target 0 lun 0 (pass0,da0)
<SUPER GEM318 0>                   at scbus0 target 6 lun 0 (pass1)
<  >                               at scbus0 target -1 lun -1 ()
scbus1 on asr0 bus 1:
<IFT ES A08U-G 331J>               at scbus1 target 0 lun 0 (pass2,da1)
<IFT ES A08U-G 331J>               at scbus1 target 0 lun 1 (pass3,da2)
<  >                               at scbus1 target -1 lun -1 ()
scbus-1 on xpt0 bus 0:
<  >                               at scbus-1 target -1 lun -1 (xpt0)
### Output of dmesg on FreeBSD 4.10-RELEASE:
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.10-RELEASE #0: Wed Jul  7 10:58:02 CEST 2004
    root@localhost:/usr/src/sys/compile/MYKERNEL07072004
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2799.70-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 1073217536 (1048064K bytes)
avail memory = 1039151104 (1014796K bytes)
Preloaded elf kernel "kernel" at 0xc054d000.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 24 entries at 0xc00fde40
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci1
pci2: <PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port
0x3000-0x303f mem 0xf8200000-0xf821ffff irq 5 at device 3.0 on pci2
em0:  Speed:N/A  Duplex:N/A
em1: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port
0x3040-0x307f mem 0xf8220000-0xf823ffff irq 5 at device 3.1 on pci2
em1:  Speed:N/A  Duplex:N/A
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
pci3: <PCI bus> on pcib3
asr0: <Adaptec Caching SCSI RAID> mem
0xfc000000-0xfdffffff,0xfb000000-0xfbffffff,0xf8300000-0xf83fffff irq 5
at device 3.0 on pci3
asr0: major=154
asr0: ADAPTEC 2015S FW Rev. 3B05, 2 channel, 256 CCBs, Protocol I2O
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port
0x2000-0x201f irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port
0x2020-0x203f irq 10 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port
0x2040-0x205f irq 7 at device 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
pci4: <PCI bus> on pcib4
pci4: <ATI Mach64-GR graphics accelerator> at 1.0 irq 11
isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port
0x2060-0x206f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 irq 0 at
device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 0
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcafff,0xcb000-0xd0fff,0xe0000-0xe3fff 
on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: parallel port not found.
acd0: CDROM <CD-224E> at ata1-master PIO4
em0: Link is up 100 Mbps Full Duplex
pass1 at asr0 bus 0 target 6 lun 0
pass1: <SUPER GEM318 0> Fixed Processor SCSI-2 device
da0 at asr0 bus 0 target 0 lun 0
da0: <ADAPTEC RAID-1 3B05> Fixed Direct Access SCSI-2 device
da0: Tagged Queueing Enabled
da0: 35003MB (71686144 512 byte sectors: 255H 63S/T 4462C)
da1 at asr0 bus 1 target 0 lun 0
da1: <IFT ES A08U-G 331J> Fixed Direct Access SCSI-3 device
da1: Tagged Queueing Enabled
da1: 714641MB (1463586799 512 byte sectors: 255H 63S/T 25568C)
da2 at asr0 bus 1 target 0 lun 1
da2: <IFT ES A08U-G 331J> Fixed Direct Access SCSI-3 device
da2: Tagged Queueing Enabled
da2: 714641MB (1463586799 512 byte sectors: 255H 63S/T 25568C)
Mounting root from ufs:/dev/da0s1a
em0: Link is up 100 Mbps Full Duplex
### Output of scanpci on FreeBSD 4.10-RELEASE:
pci bus 0x0000 cardnum 0x00 function 0x00: vendor 0x8086 device 0x254c
Intel Corp.  Device unknown
pci bus 0x0000 cardnum 0x00 function 0x01: vendor 0x8086 device 0x2541
Intel Corp. e7500 [Plumas] DRAM Controller Error Reporting
pci bus 0x0000 cardnum 0x02 function 0x00: vendor 0x8086 device 0x2543
Intel Corp. e7500 [Plumas] HI_B Virtual PCI Bridge (F0)
pci bus 0x0000 cardnum 0x1d function 0x00: vendor 0x8086 device 0x2482
Intel Corp. 82801CA/CAM USB (Hub #1)
pci bus 0x0000 cardnum 0x1d function 0x01: vendor 0x8086 device 0x2484
Intel Corp. 82801CA/CAM USB (Hub #2)
pci bus 0x0000 cardnum 0x1d function 0x02: vendor 0x8086 device 0x2487
Intel Corp. 82801CA/CAM USB (Hub #3)
pci bus 0x0000 cardnum 0x1e function 0x00: vendor 0x8086 device 0x244e
Intel Corp. 82801BA/CA/DB PCI Bridge
pci bus 0x0000 cardnum 0x1f function 0x00: vendor 0x8086 device 0x2480
Intel Corp. 82801CA ISA Bridge (LPC)
pci bus 0x0000 cardnum 0x1f function 0x01: vendor 0x8086 device 0x248b
Intel Corp. 82801CA IDE U100
pci bus 0x0000 cardnum 0x1f function 0x03: vendor 0x8086 device 0x2483
Intel Corp. 82801CA/CAM SMBus
pci bus 0x0001 cardnum 0x1c function 0x00: vendor 0x8086 device 0x1461
Intel Corp. 82870P2 P64H2 I/OxAPIC
pci bus 0x0001 cardnum 0x1d function 0x00: vendor 0x8086 device 0x1460
Intel Corp. 82870P2 P64H2 Hub PCI Bridge
pci bus 0x0001 cardnum 0x1e function 0x00: vendor 0x8086 device 0x1461
Intel Corp. 82870P2 P64H2 I/OxAPIC
pci bus 0x0001 cardnum 0x1f function 0x00: vendor 0x8086 device 0x1460
Intel Corp. 82870P2 P64H2 Hub PCI Bridge
pci bus 0x0002 cardnum 0x03 function 0x00: vendor 0x8086 device 0x1010
Intel Corp. 82546EB Gigabit Ethernet Controller (Copper)
pci bus 0x0002 cardnum 0x03 function 0x01: vendor 0x8086 device 0x1010
Intel Corp. 82546EB Gigabit Ethernet Controller (Copper)
pci bus 0x0003 cardnum 0x03 function 0x00: vendor 0x1044 device 0xa511
Distributed Processing Technology SmartRAID V Controller
pci bus 0x0004 cardnum 0x01 function 0x00: vendor 0x1002 device 0x4752
ATI Technologies Inc Rage XL
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"

• Previous message: dvv: "Re: SPARC2"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Relevant Pages Re: FreeBSD 7.0 + Xen 3.1 + HVM: Success! ... FreeBSD won't run on Xen 3.1 in HVM on Intel ... # Memory and CPU settings ... configured irq 4 not in bitmap of probed irqs 0 ... (freebsd-stable) Re: [PATCH] [broken?] Add MSI support to e1000 ... 0000:00:01.0 System peripheral: Intel Corp. Memory Controller Hub DMA Controller ... 0000:02:00.0 PCI bridge: Intel Corp. PCI Bridge Hub A ... 0000:02:00.1 PIC: Intel Corp. PCI Bridge Hub I/OxAPIC Interrupt Controller A ... (Linux-Kernel) PROBLEM: Multicast reception fail when setsockopt() used to set SO_RCVBUF to small. ... I used setsockoptto set the receive buffer size for multicast reception. ... c800-c8ff: Intel ICH4 ... d000-efff: PCI Bus #02 ... Intel Corp. 82801DB Ultra ATA Storage Controller ... (Linux-Kernel) Re: Status of 6.0 for production systems ... >what happens on FreeBSD. ... >through my mind is the support future world energy needs. ... >things that aren't ideally power efficient. ... >A lot of people wondered how Steve Jobs could dare change over to Intel chips. ... (freebsd-questions) Re: Intel Macs, FreeBSD, and drivers ... will that driver work under FreeBSD? ... a very new Intel Mac has a new disk controller, ... (freebsd-questions)