Re: FBSD 2.5.1-p11 | Promise SATA150 TX2plus | Seagate B 200GB - BAD SUPERBLK / Machine freezes up etc

From: Sebastian Holmqvist (sebastian.holmqvist_at_gmail.com)
Date: 11/08/04

  • Next message: Alan Gerber: "Re: difference between releases" 
    Date: Mon, 8 Nov 2004 20:04:59 +0100
To: freebsd-questions@freebsd.org

    "I've been getting WRITE_DMA timeouts in /var/log/messages though,
    typically 1 to 3 of them before the lockup. Have you noticed any of
    these?"
    Nope, nothing of that kind.
    Can't check for earlier times since I've reinstalled since then. But
    the error tonight didn't report anything.

    Please get back to me if you manage to survive any large data-transfers :)
    In that case; "5.3 HERE I COME" :p

    ------------
    Sebastian Holmqvist

    On Mon, 8 Nov 2004 13:42:57 -0500, Louis LeBlanc <freebsd@keyslapper.org> wrote:
    > On 11/08/04 06:57 PM, Sebastian Holmqvist sat at the `puter and typed:
    >
    >
    > > Hi, I'm running a FBSD 5.2.1-p11 server on a 350 PII.
    > > 1 IDE is plugged in on the motherboard. The other two Seagate
    > > Barracuda 200 GB SATA discs are plugged in on the controllercard.
    > >
    > > I get bad geometry in sysinstall (which is apparently a bug as far as
    > > I know from searching old mail-lists). Fdisk states that 387621/16/63
    > > is wrong. Inside is changes to 24321/255/63.
    > > ST3200822AS is the product name for the hard-drive.
    > > http://www.seagate.com/cda/products/discsales/personal/family/0,1085,599,00.html
    > > is the data***.
    > >
    > > My problem is when I transfer large amounts of data to any of the discs.
    > > WIthout warning, the whole system absolutely freeze up and I have to
    > > manually reboot.
    > > When I then run fsck it reports on several problems, among them a
    > > SUPERBLK ERROR. I take it that's not good :p
    > > The disc has to be formatted and we go again.
    > >
    > > The first time it happened, I acquired a fan since they seemed a tad
    > > hot.. They were pushing 60°C. They are now around 35°C idle. High load
    > > is probably putting them around 45°C I believe.
    > >
    > >
    > > These are the theories I've come up with:
    > > 1) Both my discs are bad (brand new when I bought them)
    > > 2) The setup with the controller card and the motherboard doesn't work
    > > 3) FBSD can't handle the data-transfer very well after a while. Could
    > > it be that the data goes to the IDE and then to the SATA-discs?
    > >
    > > Thanks in advance, I really don't know how to handle this. Or, well
    > > I'm gonna try updating to 5.3 in a couple of days, since they have
    > > better SATA-handling I've been told.
    >
    > I've had problems with an Intel ICH5 SATA controller, and serious system
    > lockups much like what you're describing.
    >
    > I've run my drive through every utility I could find and I'm convinced
    > there's nothing wrong with it.
    >
    > I've been getting WRITE_DMA timeouts in /var/log/messages though,
    > typically 1 to 3 of them before the lockup. Have you noticed any of
    > these?
    >
    > I hadn't thought about the fdisk issue, but yesterday I did a new 5.3
    > install and got a similar message to yours.
    >
    > Based on the fdisk message, I'm going to keep an eye out for anything
    > strange. I haven't had this problem in 5.3 yet, but if I do, I'll be
    > sure to look up the drives data *** (WD 160G) and see how they match.
    > In the past, I've always let fdisk do what it wanted, but maybe I should
    > have forced it to the mfg spec. Perhaps I'll retry the install using
    > that method. If it changes anything, I'll post it here.
    >
    > Not sure this helps, but maybe it'll put a couple pieces of the puzzle
    > together somewhere.
    >
    > Good luck
    > Lou
    > --
    > Louis LeBlanc FreeBSD@keyslapper.org
    > Fully Funded Hobbyist, KeySlapper Extrordinaire :)
    > http://www.keyslapper.org Ô¿Ô¬
    >
    > The universe seems neither benign nor hostile, merely indifferent.
    > -- Sagan
    > _______________________________________________
    > freebsd-questions@freebsd.org mailing list
    > http://lists.freebsd.org/mailman/listinfo/freebsd-questions
    > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
    >
    _______________________________________________
    freebsd-questions@freebsd.org mailing list
    http://lists.freebsd.org/mailman/listinfo/freebsd-questions
    To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"

  • Next message: Alan Gerber: "Re: difference between releases"