Re: more problems with 5.3 and "TIMEOUT - WRITE_DMA" [SOLOTION]
From: Mike Daemon (mike.daemon_at_gmail.com)
Date: 04/07/05
- Previous message: Christopher Lane: "Re: Sysinstall + CVSup or just CVSup?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Thu, 7 Apr 2005 17:15:57 +0200 To: FreeBSD Questions <freebsd-questions@freebsd.org>
On Mar 27, 2005 11:47 PM, Mike Daemon <mike.daemon@gmail.com> wrote:
> On Sun, 27 Mar 2005 13:32:43 -0800, Thomas Foster <tbonius@comcast.net> wrote:
> > I had this same issue
>
> I´ll have seen some more posts on the list with about the same problem
> therefore, I hope some bright one will take alook at the code.. and
> post something smart.. I´m very much stuck, hopeing any new snapshot
> will work..
>
> on an older AMD Nforce board. 5.2.1 seemed to install
> > and run.. but moving to 5.3 gave me issues. I tinkered with the DMA
> > settings in the BIOS.. to no avail. The Geometry seemed to be off on the
> > drive I noticed (IBM deskstar) when I newfs'd it.. so I changed out drives..
> > but never got it working.. I eventually just dropped Gentoo on it.
> >
> > What chipset, drive controller hard drive are you using on this system?
>
> http://www.freebsd.org/cgi/man.cgi?query=ata&sektion=4&manpath=FreeBSD+5.3-RELEASE
>
> I´ll notised that my idecontroller IS supported by the ata-driver,
> witch makes it even stranger.. (I think I will check on my cabling
> once more, even if it´s a newly installed _rounded_ 32 pin cable..)
>
> My atacontroller: SiS 5513
> My HDD: Seagate 200 GB
>
>
> >
> > T
> >
> > ----- Original Message -----
> > From: "Mike Daemon" <mike.daemon@gmail.com>
> > To: "FreeBSD Questions" <freebsd-questions@freebsd.org>
> > Sent: Sunday, March 27, 2005 1:15 PM
> > Subject: more problems with 5.3 and "TIMEOUT - WRITE_DMA"
> >
> > I got this annoying problem when upgradeing to 5.3, the miniinst iso
> > blurps out "TIMEOUT - WRITE_DMA" when it starts writing base to my
> > disk. And when I tried to first install 5.2.1 and upgrade (cvsup, make
> > buildworld etc.. ) to 5.3 that way everything seems fine until I
> > reboot to single-user-mode, as soon as Im starting to write anything
> > to the disk it´s blurping out those errors.. I have diagnosticed my
> > disk, checked my cabling and fixed my PSU (installed a brand new one).
> > No difference. I noticed that my ide-controller was supported in 4.11,
> > but not? in 5.3, is that realy true? seems very strange...
> >
> > Sence I duel boot with Wintendo/Lunix and don´t see this problem with
> > those oses I´m very confused of what to do next..
> >
> > I´ll tried some snapshots to but no luck...
> >
> > / Mike
> >
> > ps My dmesg goes in the attachment, in hope for a patch/solution to
> > this problem. ds
> >
> > --------------------------------------------------------------------------------
> >
> > > _______________________________________________
> > > freebsd-questions@freebsd.org mailing list
> > > http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> > > To unsubscribe, send any mail to
> > > "freebsd-questions-unsubscribe@freebsd.org"
> > >
> >
I (with a little help from a good friend ) figured out an solution to
the problem, in switching my brand new ata133 ide-cable to an "old
school" ata33 ide-cable FreeBSD sets my drives to UDMA3 and boots up
alright..
key commands here:
atacontrol list
and
atacontrol mode <channel number>
( my buddy had come across some message telling about how SiS had
created an new "SiS 5513" chipset with the same tag.. unfortunal he
didn't remember where that message were. But it would make sense why
FreeBSD tryies to use UDMA5 on my UDMA3 only atachipset.. )
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
- Previous message: Christopher Lane: "Re: Sysinstall + CVSup or just CVSup?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
