Re: 5.4 reboots when I plug in a flash drive?
From: Brian John (brianjohn_at_fusemail.com)
Date: 10/05/05
- Previous message: sulie halim: "Password"
- In reply to: Lowell Gilbert: "Re: 5.4 reboots when I plug in a flash drive?"
- Next in thread: Lowell Gilbert: "Re: 5.4 reboots when I plug in a flash drive?"
- Reply: Lowell Gilbert: "Re: 5.4 reboots when I plug in a flash drive?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Tue, 04 Oct 2005 20:36:37 -0500 To: freebsd-questions@freebsd.org
Lowell Gilbert wrote:
>Brian John <brianjohn@fusemail.com> writes:
>
>
>
>>Parv wrote:
>>
>>
>>
>>>in message
>>><1468.209.87.176.132.1128439684.fusewebmail-19592@webmail.fusemail.com
>>>
>>>
>>>
>>>>, wrote Brian John thusly...
>>>>
>>>>I just got a 128MB USB flash drive. When I plug it in in FreeBSD,
>>>>the box promptly reboots! What would cause this?
>>>>
>>>>
>>>>
>>>I don't know the cause.
>>>
>>>Have you tried booting FreeBSD from power-off state w/ the flash
>>>drive already inserted? That may solve your booting problem, but
>>>will not make use of the drive any easier.
>>>
>>>Which version if FreeBSD are you using? Which of the [ueo]hci
>>>drivers come up in dmesg(8) on instertion of the USB drive?
>>>
>>>
>>> - Parv
>>>
>>>
>>>
>>>
>>Ok, I tried booting up with the drive installed. If I leave it
>>installed while it is booting up, it eventually reboots. However, I
>>was able to unplug it during boot and look at dmesg. It says this
>>over and over again:
>>
>>umass0: vendor 0x10d6 USB 2.0(FS) FLASH DISK, rev 1.10/1.00, addr 2
>>da0 at umass-sim0 bus 0 target 0 lun 0
>>da0: <USB2.0 (FS) FLASH DISK 1.00> Removable Direct Access SCSI-0 device
>>da0: 1.000MB/s transfers
>>da0: 119MB (245473 512 byte sectors: 64H 32S/T 119C)
>>umass0: BBB reset failed, STALLED
>>umass0: BBB bulk-in clear stall failed, STALLED
>>umass0: BBB bulk-out clear stall failed, STALLED
>>(da0:umass-sim0:0:0:0): Synchronize cache failed, status == 0x4, scsi
>>status == 0x0
>>umass0: BBB reset failed, STALLED
>>umass0: BBB bulk-in clear stall failed, STALLED
>>umass0: BBB bulk-out clear stall failed, STALLED
>>umass0: BBB reset failed, STALLED
>>umass0: BBB bulk-in clear stall failed, STALLED
>>umass0: BBB bulk-out clear stall failed, STALLED
>>umass0: BBB reset failed, STALLED
>>umass0: BBB bulk-in clear stall failed, STALLED
>>umass0: BBB bulk-out clear stall failed, STALLED
>>umass0: BBB reset failed, STALLED
>>umass0: BBB bulk-in clear stall failed, STALLED
>>umass0: BBB bulk-out clear stall failed, STALLED
>>umass0: BBB reset failed, STALLED
>>umass0: BBB bulk-in clear stall failed, STALLED
>>umass0: BBB bulk-out clear stall failed, STALLED
>>umass0: at uhub2 port 1 (addr 2) disconnected
>>(da0:umass-sim0:0:0:0): lost device
>>(da0:umass-sim0:0:0:0): removing device entry
>>Opened disk da0 -> 5
>>umass0: detached
>>
>>I am running FreeBSD 5.4. Does this shed some light on the problem?
>>
>>
>
>Only a little. Do you have udbp(4) in your kernel?
>Can you try booting 6.0 with the flash unit plugged in and see if it
>still has problems?
>
>
>
I could try it, but I don't want to have to roll 6.0 back to 5.4
afterward if it doesn't work. Upgrading to 6.0 is a major change and I
only have 1 PC. I am still kind of a novice, how easy is it to upgrade
to 6.0 and how stable is it? I see that I have the line with udbp
commented out in my kernel config. Should I rebuild with it uncommented?
#device udbp # USB Double Bulk Pipe devices
Thanks
/Brian
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
- Previous message: sulie halim: "Password"
- In reply to: Lowell Gilbert: "Re: 5.4 reboots when I plug in a flash drive?"
- Next in thread: Lowell Gilbert: "Re: 5.4 reboots when I plug in a flash drive?"
- Reply: Lowell Gilbert: "Re: 5.4 reboots when I plug in a flash drive?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
