6.0 panics on boot

From: Derek Ragona (derek_at_computinginnovations.com)
Date: 11/07/05

  • Next message: Peter Clutton: "Re: Freebsd install" 
    Date: Sun, 06 Nov 2005 18:29:14 -0600
To: freebsd-questions@freebsd.org

    I have a computer that has been running FreeBSD 4.X and 5.X without
    problems. It runs 5.4 with no problems at all. This system has an Intel
    845 Motherboard and chipset, Intel Pentium 4 1.6 GHz CPU, 1 GB RAM, NVidea
    GEForce MX/MX 400 video card, atapi CD-RW, IDE hard drive, standard
    floppy. Nothing very exotic in this hardware.

    I tried first to cvsup to 6.0, and rebuild everything. The build was fine
    including a custom kernel, but when I tried to boot the new 6.0, I got a
    panic, Fatal trap 12, page fault at the NVidea driver in the boot. So I
    re-booted the kernel.old, reverted my sources to 5.4 and rebuilt the system
    all again.

    As the system rebuilt I downloaded and burned the ISO 6.0 image.

    I tried to boot the ISO image and do a binary upgrade. The CD booted 6.0
    fine, and the upgrade installed with only one error that the X.org was
    already present. When I tried to boot the new 6.0 GENERIC kernel that was
    installed, I got the same panic/page fault error I had when I updated via
    cvsup.

    But since the same GENERIC kernel boots fine from CD I suspect there may be
    some loader options I might need? I'd appreciate any help with getting 6.0
    to boot without the panic.

    Thanks

    Here is the dmesg from the last boot to give any details anyone might want
    on this system:
    =============================================================
    Copyright (c) 1992-2005 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
             The Regents of the University of California. All rights reserved.
    FreeBSD 5.4-RELEASE-p8 #1: Sat Nov 5 23:43:05 CST 2005
         root@betty.computinginnovations.com:/usr/obj/usr/src/sys/BETTY
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Pentium(R) 4 CPU 1600MHz (1594.83-MHz 686-class CPU)
       Origin = "GenuineIntel" Id = 0xf0a Stepping = 10
       Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
    real memory = 1073479680 (1023 MB)
    avail memory = 1036734464 (988 MB)
    ACPI APIC Table: <D845HV HV84510A>
    ioapic0: Changing APIC ID to 2
    ioapic0 <Version 2.0> irqs 0-23 on motherboard
    npx0: <math processor> on motherboard
    npx0: INT 16 interface
    acpi0: <D845HV WN84510A> on motherboard
    acpi0: Power Button (fixed)
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
    cpu0: <ACPI CPU> port 0x530-0x537 on acpi0
    acpi_button0: <Power Button> on acpi0
    pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
    pci0: <ACPI PCI bus> on pcib0
    agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xefffffff at device
    0.0 on pci0
    pcib1: <PCI-PCI bridge> at device 1.0 on pci0
    pci1: <PCI bus> on pcib1
    nvidia0: <GeForce2 MX/MX 400> mem
    0xd0000000-0xd7ffffff,0xfd000000-0xfdffffff irq 16 at device 0.0 on pci1
    pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
    pci2: <ACPI PCI bus> on pcib2
    dc0: <LC82C115 PNIC II 10/100BaseTX> port 0xd800-0xd8ff mem
    0xfeaffc00-0xfeaffcff irq 23 at device 11.0 on pci2
    miibus0: <MII bus> on dc0
    dcphy0: <Intel 21143 NWAY media interface> on miibus0
    dcphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    dc0: Ethernet address: 00:00:94:c8:52:68
    dc0: if_start running deferred for Giant
    isab0: <PCI-ISA bridge> at device 31.0 on pci0
    isa0: <ISA bus> on isab0
    atapci0: <Intel ICH2 UDMA100 controller> port
    0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
    ata0: channel #0 on atapci0
    ata1: channel #1 on atapci0
    uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0xef40-0xef5f
    irq 19 at device 31.2 on pci0
    usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
    usb0: USB revision 1.0
    uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub0: 2 ports with 2 removable, self powered
    pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
    uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0xef80-0xef9f
    irq 23 at device 31.4 on pci0
    usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
    usb1: USB revision 1.0
    uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub1: 2 ports with 2 removable, self powered
    pcm0: <Intel ICH2 (82801BA)> port 0xef00-0xef3f,0xe800-0xe8ff irq 17 at
    device 31.5 on pci0
    pcm0: <Analog Devices AD1885 AC97 Codec>
    atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
    atkbd0: <AT Keyboard> irq 1 on atkbdc0
    kbd0 at atkbd0
    psm0: <PS/2 Mouse> irq 12 on atkbdc0
    psm0: model IntelliMouse, device ID 3
    fdc0: <floppy drive controller> port
    0x3f7,0x3f4-0x3f5,0x3f2-0x3f3,0x3f0-0x3f1 irq 6 drq 2 on acpi0
    fd0: <1440-KB 3.5" drive> on fdc0 drive 0
    sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    sio0: type 16550A
    ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
    ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
    ppbus0: <Parallel port bus> on ppc0
    lpt0: <Printer> on ppbus0
    lpt0: Interrupt-driven port
    ppi0: <Parallel I/O> on ppbus0
    orm0: <ISA Option ROM> at iomem 0xc0000-0xcc7ff on isa0
    pmtimer0 on isa0
    sc0: <System console> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sio1: configured irq 3 not in bitmap of probed irqs 0
    sio1: port may not be enabled
    vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    uhub2: Intel product 0x1120, class 9/0, rev 1.10/0.00, addr 2
    uhub2: 4 ports with 4 removable, self powered
    Timecounter "TSC" frequency 1594831964 Hz quality 800
    Timecounters tick every 10.000 msec
    ad0: 117246MB <Maxtor 6Y120L0/YAR41BW0> [238216/16/63] at ata0-master UDMA100
    acd0: CDRW <CD-W516EB/1.0B> at ata1-master PIO4
    cd0 at ata1 bus 0 target 0 lun 0
    cd0: <TEAC CD-W516EB 1.0B> Removable CD-ROM SCSI-0 device
    cd0: 16.000MB/s transfers
    cd0: Attempt to query device size failed: NOT READY, Medium not present
    Mounting root from ufs:/dev/ad0s1a

    _______________________________________________
    freebsd-questions@freebsd.org mailing list
    http://lists.freebsd.org/mailman/listinfo/freebsd-questions
    To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"

  • Next message: Peter Clutton: "Re: Freebsd install"

    Relevant Pages

    • Re: System Freezing -Again
      ... I'd guess you have an irq problem, the @'s sound like a mail bomb of some kind, but my server's get that all the time. ... pci0: <PCI bus> on pcib0 ... 16 at device 29.0 on pci0 ... ppc0: parallel port not found. ...
      (freebsd-questions)
    • System Still Freezing
      ... I ran every 32 bit Dell diagnostic I could on it ... ... pci0: <PCI bus> on pcib0 ... ppc0: parallel port not found. ...
      (freebsd-questions)
    • RE: Problem with foppy drive
      ... I think I see your problem in the boot log. ... <ACPI PCI bus> on pcib0 ... <Parallel port bus> on ppc0 ... on ppbus0 ...
      (freebsd-questions)
    • FreeBSD 6.0 kernel panic
      ... FreeBSD 6.0, although that is not necessary for FreeBSD 5.4. ... pci0: <PCI bus> on pcib0 ... <Parallel port bus> on ppc0 ...
      (comp.unix.bsd.freebsd.misc)
    • "ffs_mountroot: cant find rootvp" after cvsup and making worldfmen
      ... installed the world and a new kernel. ... When I boot the new kernel, ... <ACPI PCI bus> on pcib0 ... <Standard parallel printer port> port 0x778-0x77b,0x378-0x37f irq ...
      (freebsd-stable)