only first PCMCIA card works

Dear list

Running FreeBSD-6.1 RELEASE on Thinkpad 380XD, I have been using this
notebook for many years (and used FreeBSD from 4.7 to 6.1). An ethernet
card is plugged on the first PCMCIA slot and I inserted my FC card
reader (PCMCIA card produced by Hitachi) and noticed it's not detected
(no message about it in dmesg)

Later I discovered any card in the first PCMCIA slot works, any card in
second slot, be it ethernet card or FC card adapter, doesn't work.

I have pccard_enable="YES" in my rc.conf. dmesg told me this:

# dmesg | grep pccard
pccard0: <16-bit PCCard bus> on cbb0
pccard1: <16-bit PCCard bus> on cbb1
ep0: <3Com Corporation 3C589D> at port 0x100-0x10f irq 11 function 0 config 1 on pccard0

Actually I am not sure what to do next. I checked dmesg and found irq 11
is used by uchi0, as well as ep0, surprisingly both works, maybe my
knowledge of IRQ is outdated. I also checked that my IRQ 3, 4 and 10 are
not used (3 & 4 are free because my sio hardware is borken so I disabled
it in /boot/devices.hint), so I write /etc/pccard.conf which says:

irq 3 4 10

But after reboot the ep0 device still get 10 (I suspect it can get 3?)
Then I go to added this to /boot/devices:

hint.uhci.0.at="pci"
hint.uhci.0.irq="3"

After reboot uchi0 is still at irq 11. Strange.

I attached both of my dmesg and kernel config file.

Thanks for suggestions and hints on hardware knowledge to me!
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ../../conf/NOTES and NOTES files.
# If you are in doubt as to the purpose or necessity of a line, check first
# in NOTES.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.429.2.7.2.2 2006/05/01 00:15:12 scottl Exp $

machine i386
cpu I586_CPU
ident QUASIMODO


# To statically compile in device wiring instead of /boot/device.hints
#hints "GENERIC.hints" # Default places to look for devices.

makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols

options VESA
options VGA_WIDTH90
options SC_PIXEL_MODE
#options SCHED_ULE # ULE scheduler
options SCHED_4BSD # 4BSD scheduler
options PREEMPTION # Enable kernel thread preemption
options INET # InterNETworking
options INET6 # IPv6 communications protocols
options FFS # Berkeley Fast Filesystem
options SOFTUPDATES # Enable FFS soft updates support
options UFS_ACL # Support for access control lists
options UFS_DIRHASH # Improve performance on big directories
options MD_ROOT # MD is a potential root device
options NFSCLIENT # Network Filesystem Client
options NFSSERVER # Network Filesystem Server
options NFS_ROOT # NFS usable as /, requires NFSCLIENT
options MSDOSFS # MSDOS Filesystem
options CD9660 # ISO 9660 Filesystem
options PROCFS # Process filesystem (requires PSEUDOFS)
options PSEUDOFS # Pseudo-filesystem framework
options GEOM_GPT # GUID Partition Tables.
options COMPAT_43 # Compatible with BSD 4.3 [KEEP THIS!]
options COMPAT_FREEBSD4 # Compatible with FreeBSD4
options COMPAT_FREEBSD5 # Compatible with FreeBSD5
options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI
options KTRACE # ktrace(1) support
options SYSVSHM # SYSV-style shared memory
options SYSVMSG # SYSV-style message queues
options SYSVSEM # SYSV-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~128k to driver.
options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.
options ADAPTIVE_GIANT # Giant mutex is adaptive.

device apic # I/O APIC

# Bus support.
device eisa
device pci

# Floppy drives
device fdc

# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device ataraid # ATA RAID drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID # Static device numbering

# SCSI Controllers
device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
device ahd # AHA39320/29320 and onboard AIC79xx devices
device amd # AMD 53C974 (Tekram DC-390(T))
device isp # Qlogic family
#device ispfw # Firmware for QLogic HBAs- normally a module
device mpt # LSI-Logic MPT-Fusion
#device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets + those of `ncr')
device trm # Tekram DC395U/UW/F DC315U adapters

device adv # Advansys SCSI adapters
device adw # Advansys wide SCSI adapters
device aha # Adaptec 154x SCSI adapters
device aic # Adaptec 15[012]x SCSI adapters, AIC-6[23]60.
device bt # Buslogic/Mylex MultiMaster SCSI adapters

device ncv # NCR 53C500
device nsp # Workbit Ninja SCSI-3
device stg # TMC 18C30/18C50

# SCSI peripherals
device scbus # SCSI bus (required for SCSI)
device ch # SCSI media changers
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
device ses # SCSI Environmental Services (and SAF-TE)

# RAID controllers interfaced to the SCSI subsystem
device amr # AMI MegaRAID
device arcmsr # Areca SATA II RAID
device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
device ciss # Compaq Smart RAID 5*
device dpt # DPT Smartcache III, IV - See NOTES for options
device hptmv # Highpoint RocketRAID 182x
device rr232x # Highpoint RocketRAID 232x
device iir # Intel Integrated RAID
device ips # IBM (Adaptec) ServeRAID
device mly # Mylex AcceleRAID/eXtremeRAID
device twa # 3ware 9000 series PATA/SATA RAID

# RAID controllers
device aac # Adaptec FSA RAID
device aacp # SCSI passthrough for aac (requires CAM)
device ida # Compaq Smart RAID
device mfi # LSI MegaRAID SAS
device mlx # Mylex DAC960 family
device pst # Promise Supertrak SX6000
device twe # 3ware ATA RAID

# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse

device kbdmux # keyboard multiplexer

device vga # VGA video card driver

device splash # Splash screen and screen saver support

# syscons is the default console driver, resembling an SCO console
device sc

# Enable this for the pcvt (VT220 compatible) console driver
#device vt
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor

device agp # support several AGP chipsets

# Power management support (see NOTES for more options)
device apm
# Add suspend/resume support for the i8254.
device pmtimer

# PCCARD (PCMCIA) support
# PCMCIA and cardbus bridge support
device cbb # cardbus (yenta) bridge
device pccard # PC Card (16-bit) bus

# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports

# Parallel port
device ppc
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da

# If you've got a "dumb" serial or parallel PCI card that is
# supported by the puc(4) glue driver, uncomment the following
# line to enable it (connects to the sio and/or ppc drivers):
#device puc

# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device em # Intel PRO/1000 adapter Gigabit Ethernet Card
device ixgb # Intel PRO/10GbE Ethernet Card
device txp # 3Com 3cR990 (``Typhoon'')
device vx # 3Com 3c590, 3c595 (``Vortex'')

# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device bce # Broadcom BCM5706/BCM5708 Gigabit Ethernet
device bfe # Broadcom BCM440x 10/100 Ethernet
device bge # Broadcom BCM570xx Gigabit Ethernet
device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device lge # Level 1 LXT1001 gigabit Ethernet
device nge # NatSemi DP83820 gigabit Ethernet
device nve # nVidia nForce MCP on-board Ethernet Networking
device pcn # AMD Am79C97x PCI 10/100(precedence over 'lnc')
device re # RealTek 8139C+/8169/8169S/8110S
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS 7016
device sk # SysKonnect SK-984x & SK-982x gigabit Ethernet
device ste # Sundance ST201 (D-Link DFE-550TX)
device ti # Alteon Networks Tigon I/II gigabit Ethernet
device tl # Texas Instruments ThunderLAN
device tx # SMC EtherPower II (83c170 ``EPIC'')
device vge # VIA VT612x gigabit Ethernet
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')

# ISA Ethernet NICs. pccard NICs included.
device cs # Crystal Semiconductor CS89x0 NIC
# 'device ed' requires 'device miibus'
device ed # NE[12]000, SMC Ultra, 3c503, DS8390 cards
device ex # Intel EtherExpress Pro/10 and Pro/10+
device ep # Etherlink III based cards
device fe # Fujitsu MB8696x based cards
device ie # EtherExpress 8/16, 3C507, StarLAN 10 etc.
device lnc # NE2100, NE32-VL Lance Ethernet cards
device sn # SMC's 9000 series of Ethernet chips
device xe # Xircom pccard Ethernet

# Wireless NIC cards
device wlan # 802.11 support
device an # Aironet 4500/4800 802.11 wireless NICs.
device awi # BayStack 660 and others
device ral # Ralink Technology RT2500 wireless NICs.
device wi # WaveLAN/Intersil/Symbol 802.11 wireless NICs.
#device wl # Older non 802.11 Wavelan wireless NIC.

# Pseudo devices.
device loop # Network loopback
device random # Entropy device
device ether # Ethernet support
device sl # Kernel SLIP
device ppp # Kernel PPP
device tun # Packet tunnel.
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
device gif # IPv6 and IPv4 tunneling
device faith # IPv6-to-IPv4 relaying (translation)

# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
# Note that 'bpf' is required for DHCP.
device bpf # Berkeley packet filter

# USB support
device uhci # UHCI PCI->USB interface
# I don't have below equipments
##device ohci # OHCI PCI->USB interface
##device ehci # EHCI PCI->USB interface (USB 2.0)
device usb # USB Bus (required)
#device udbp # USB Double Bulk Pipe devices
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device ural # Ralink Technology RT2500USB wireless NICs
device urio # Diamond Rio 500 MP3 player
device uscanner # Scanners
# USB Ethernet, requires miibus
device aue # ADMtek USB Ethernet
device axe # ASIX Electronics USB Ethernet
device cdce # Generic USB over Ethernet
device cue # CATC USB Ethernet
device kue # Kawasaki LSI USB Ethernet
device rue # RealTek RTL8150 USB Ethernet
# USB to serial converter
device uplcom
device ucom

# FireWire support
device firewire # FireWire bus code
device sbp # SCSI over FireWire (Requires scbus and da)
device fwe # Ethernet over FireWire (non-standard!)
device sound
device snd_csa # to drive CS423x sound card
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE #2: Mon Jan 22 23:37:50 CST 2007
root@xxxxxxxxxxxxxxxxxxxx:/usr/obj/usr/src/sys/QUASIMODO
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium/P55C (quarter-micron) (232.11-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x581 Stepping = 1
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory = 33357824 (31 MB)
avail memory = 23166976 (22 MB)
Intel Pentium detected, installing workaround for F00F bug
kbd1 at kbdmux0
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 4 Entries> on motherboard
pci0: <PCI bus> on pcib0
cbb0: <TI1250 PCI-CardBus Bridge> mem 0x20822000-0x20822fff at device 2.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <TI1250 PCI-CardBus Bridge> mem 0x20821000-0x20821fff at device 2.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
$PIR: ROUTE_INTERRUPT failed.
cbb: Unable to map IRQ...
device_attach: cbb1 attach returned 12
pci0: <display, VGA> at device 3.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 6.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfcf0-0xfcff at device 6.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x9000-0x901f irq 11 at device 6.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 6.3 (no driver attached)
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xc9fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0400> can't assign resources (port)
pcm0: <CS423x> at port 0x530-0x537,0x388-0x38b,0x220-0x233 irq 5 drq 1,0 on isa0
pcm0: [GIANT-LOCKED]
unknown: <PNP0e03> can't assign resources (port)
Timecounter "TSC" frequency 232106203 Hz quality 800
Timecounters tick every 1.000 msec
ep0: <3Com Corporation 3C589D> at port 0x100-0x10f irq 11 function 0 config 1 on pccard0
ep0: Ethernet address: 00:60:97:92:c0:27
ad0: 3102MB <IBM DTCA-23240 TC5OAB1A> at ata0-master UDMA33
acd0: CDROM <SANYO CRD-S372B/1.24F> at ata0-slave PIO3
Trying to mount root from ufs:/dev/ad0s1a
_______________________________________________
freebsd-questions@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "freebsd-questions-unsubscribe@xxxxxxxxxxx"

Relevant Pages

  • Re: project: wired/wireless router
    ... ethernet port. ... but I want to be able to provide both wired and wireless LAN access. ... I'd simply add a two or four port ethernet card to the ...
    (Debian-User)
  • multiport ethernet cards
    ... going to buy a spare PCI ethernet card. ... except on Ebay (where I can now only see one two port card). ... These two multiport ethernet adapters deliver excellent performance at ...
    (Debian-User)
  • Re: project: wired/wireless router
    ... ethernet port. ... but I want to be able to provide both wired and wireless LAN access. ... I'd simply add a two or four port ethernet card to the ...
    (Debian-User)
  • Re: Problem connecting 10BASE-5 Lan Connection to 715/64
    ... > AUI port that connects to a 4 Port MAU. ... The supported MAU for that connection ... to the card, and use an external media converter. ... course, is long out of support life, so the issue would ...
    (comp.sys.hp.hpux)
  • Re: German Atari ST users (ethernet for the ST)
    ... plugs into the Atari ACSI hard drive port). ... I don't have any ethernet abilities at all and thought the ... I really need a PCB layout so I ... RTL8019AS card. ...
    (comp.sys.atari.st)