Re[3]: Can not set up two ADSL link to provider
- From: KES <kes-kes@xxxxxxxxx>
- Date: Thu, 29 Jan 2009 18:44:32 +0200
Здравствуйте, KES.
Вы писали 27 января 2009 г., 21:23:57:
K> Здравствуйте, Chuck.
K> Вы писали 27 января 2009 г., 1:57:10:
CS>> On Jan 26, 2009, at 3:34 PM, KES wrote:
I can not setup two ADSL PPPoE Links to same provider.
Because of imposibility to setup route for second connection
First connection gets:
ng0: flags=88d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST>
metric 0 mtu 1492
inet 92.113.94.215 --> 195.5.5.203 netmask 0xffffffff
Second can not be established because of:
Jan 27 01:27:55 kes mpd: [UKR_B4] IFACE: Add address
92.113.94.249/32->195.5.5.203 to ng1
Jan 27 01:27:55 kes mpd: [UKR_B4] IFACE: Adding IPv4 address to ng1
failed: File exists
CS>> You should talk to your network provider and ask them whether they
CS>> want you to do multilink PPP or IEEE 802.3ad link aggregation. Either
CS>> way, the bonding of the two connections should give you a single
CS>> virtual network interface (tunX for the first, probably, and laggX in
CS>> the second case) which has only a single route.
CS>> For example:
CS>> http://www.juniper.net/techpubs/software/erx/junose80/swconfig-physical/html/ethernet-config14.html
CS>> ...talks about "After you configure the LAG bundle, you can route IP
CS>> traffic over it, create a VLAN over it, or route PPPoE traffic over it."
K> I do not want to aggregate links. I want use them as standalone
K> I had two servers, two lans and two ADSLs. Now I have one server, four
K> NICs: first LAN1, second LAN2, third ADSL1, forth ADSL2
K> I want to route LAN1 through ADSL1, LAN2 through ADSL2. LAN1/LAN2 must
K> not interact with each other. For each LAN I use its own FIB (routing
K> table).
K> Only one problem: I can not run setup two PPPoE link if for second
K> link is leased same gateway as for first
K> So, is it possible to workaround this problem?
In any case I is impossible to talk to my provider. It will change
nothing. This is country wide provider. They said: "if you can not
configure that on one machine then you must use two.. (((("
Also NOTICE: when I setup second PPPoE connection I setfib 1 (second
routing table). So route must be added to second routing table and
must not conflict with first, but it does
--
С уважением,
KES mailto:kes-kes@xxxxxxxxx
_______________________________________________
freebsd-questions@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "freebsd-questions-unsubscribe@xxxxxxxxxxx"
- References:
- Can not set up two ADSL link to provider
- From: KES
- Re: Can not set up two ADSL link to provider
- From: Chuck Swiger
- Re[2]: Can not set up two ADSL link to provider
- From: KES
- Can not set up two ADSL link to provider
- Prev by Date: Re: 6.8 became very slow
- Next by Date: Sendmail DNS strangeness
- Previous by thread: Re: Re[2]: Can not set up two ADSL link to provider
- Next by thread: Re: x11/libXrandr, x11-toolkits/libXmu, graphics/jasper fails to build
- Index(es):
Relevant Pages
|
