Re: issues with Intel Pro/1000 and 1000baseTX

Better yet, just let them autoneg and you won't have these problems :)

Jack


On Fri, May 15, 2009 at 9:15 AM, Steven Hartland <killing@xxxxxxxxxxxxxxx>wrote:

Never only set one end manually, always set both the machine and the
switch.

Regards
Steve

----- Original Message ----- From: "James Tanis" <jtanis@xxxxxxxxx>
To: "FreeBSD Questions" <freebsd-questions@xxxxxxxxxxx>; <
freebsd-stable@xxxxxxxxxxx>
Sent: Thursday, May 14, 2009 4:12 PM
Subject: issues with Intel Pro/1000 and 1000baseTX


I have a FreeBSD v7.0 box it has two Intel Pro/1000 NICs, the one in
question is:

em1: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
0x2020-0x203f mem 0xd8060000-0xd807ffff,0xd8040000-0xd805ffff irq 19 at
device 0.1 on pci4

what we get after boot is:

em1: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0
mtu 1500
options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4>
ether 00:30:48:xx:xx:xx
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active

The problem is that the NIC refuses to connect at 1000baseTX.

It's connected to a HP Procurve 1700-24 switch which supports 1000baseTX
on ports 23 and 24. This particular computer is connected on port 24. I have
a much older end user system which uses the same card (but earlier
revision), runs Windows XP and is plugged in to port 23. The end user system
has no problem connecting at 1000baseTX. I have of course tried switching
ports.

Attempting to force 1000baseTX via:

ifconfig em1 media 1000baseTX mediaopt full-duplex

gets me:

status: no carrier

After forcing the NIC to go 1000baseTX the LEDs on the backpane are both
off. I can only come to the conclusion that this is a driver issue based on
previous experience and the simple fact that the end user system is capable
of connecting at 1000baseTX. Anybody have any suggestions? I'm hoping I'm
wrong. I'd rather not do an in-place upgrade, this is a production system
and the main gateway for an entire school, when I do not even know for sure
whether this will fix the problem. It's worth it to me though, having a
1000baseTX uplink from the switch would remove a major bottleneck for me.

Any help would be appreciated.

--
James Tanis
Technical Coordinator
Computer Science Department
Monsignor Donovan Catholic High School

_______________________________________________
freebsd-stable@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscribe@xxxxxxxxxxx"


================================================
This e.mail is private and confidential between Multiplay (UK) Ltd. and the
person or entity to whom it is addressed. In the event of misdirection, the
recipient is prohibited from using, copying, printing or otherwise
disseminating it or any information contained in it.
In the event of misdirection, illegible or incomplete transmission please
telephone +44 845 868 1337
or return the E.mail to postmaster@xxxxxxxxxxxxxxxx

_______________________________________________
freebsd-stable@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscribe@xxxxxxxxxxx"

_______________________________________________
freebsd-questions@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "freebsd-questions-unsubscribe@xxxxxxxxxxx"

Relevant Pages

  • Re: issues with Intel Pro/1000 and 1000baseTX
    ... It's connected to a HP Procurve 1700-24 switch which supports 1000baseTX ... ports 23 and 24. ... much older end user system which uses the same card (but earlier ... Gigabit link requires CAT5e or better (CAT6). ...
    (freebsd-stable)
  • Re: Anyone successfully bonding 2 ether ports?
    ... I am a bit rusty on this, but if you setup the box with 2 ports configured with one IP address your connected layer 2 switch also needs some intelligence to know that you are running it this way. ... From memory Cisco's CDP use to get into trouble and had to be disbled if you setup a "loop" between two of their devices (eg connecting two L2 switches with two cables) in this way. ...
    (alt.os.linux.suse)
  • Re: issues with Intel Pro/1000 and 1000baseTX
    ... It's connected to a HP Procurve 1700-24 switch which supports 1000baseTX on ... much older end user system which uses the same card, ... problem connecting at 1000baseTX. ... I have of course tried switching ports. ...
    (freebsd-questions)
  • Re: issues with Intel Pro/1000 and 1000baseTX
    ... It's connected to a HP Procurve 1700-24 switch which supports 1000baseTX on ... much older end user system which uses the same card, ... problem connecting at 1000baseTX. ... I have of course tried switching ports. ...
    (freebsd-stable)
  • Re: issues with Intel Pro/1000 and 1000baseTX
    ... It's connected to a HP Procurve 1700-24 switch which supports 1000baseTX on ports 23 and 24. ... I have a much older end user system which uses the same card, runs Windows XP and is plugged in to port 23. ... I can only come to the conclusion that this is a driver issue based on previous experience and the simple fact that the end user system is capable of connecting at 1000baseTX. ...
    (freebsd-questions)
Loading