Re: Via EPIA Mini-ITX motherboard

From: Ed Hall (edhall_at_weirdnoise.com)
Date: 05/16/03

  • Next message: Don Lewis: "Re: Via EPIA Mini-ITX motherboard" 
    To: Matthew Dillon <dillon@apollo.backplane.com>
Date: Fri, 16 May 2003 12:31:59 -0700

    I have an EPIA M6000 that I use for my main workstation. I think I'm using
    the same case as Matt (Casetronic Mini-ITX-2699R) but I've put a hard drive
    (Seagate Barracuda IV, among the quietest of drives) and a slim CDROM drive
    in it. I've never seen a HDD or network problem after four months of
    near-continuous use. There's no way I could disable the fans given both
    the fanless CPU and the disk, but I put a 47-ohm 1W resistor in series
    with the fans to quiet them down. It's not silent, but it has a quiet
    purr that just blends into any ambient sounds. (It's quieter than my
    wife's IMac, for instance.)

    The onboard sound works, but there are occasional brief dropouts (system
    load makes them a bit more frequent) which depending upon source material
    are inaudible or are heard as soft clicks. Every VIA sound chip I've
    used with FreeBSD does this. Since sound is very important to me, I
    put a Turtle Beach Santa Cruz in the single PCI slot. The case uses
    an L-riser for PCI cards, and space is tight in all dimensions; I had
    to nibble a notch to get the full-width Santa Cruz to fit. But the
    card works great.

    I've not tried USB, but Firewire works fine; I use an external DVD-RW
    for backups. Just as long as I remember to have the external drive
    power on before I connect until after I disconnect, and do a manual
    Firewire bus reset after connecting (or make sure that there is valid
    media in the drive first), things work flawlessly.

    Like Matt says, you'd only get such a system if power, noise, or size
    is a strong factor. Power here in PG&E-land is a significant cost --
    I figure that my ~40W system will pay for itself in a couple of years
    compared to the average 200W drawn by most 2GHz+ boxes out there.
    But it's only a bit faster than my old 333MHz P-II -- fast enough for
    surfing, modest development, and as a front-end to other networked
    systems.

                    -Ed

    _______________________________________________
    freebsd-stable@freebsd.org mailing list
    http://lists.freebsd.org/mailman/listinfo/freebsd-stable
    To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"

  • Next message: Don Lewis: "Re: Via EPIA Mini-ITX motherboard"

    Relevant Pages

    • Re: Problems with new computer
      ... The sound card i have is nVIDIA nForce Audio ... > from 1 or both of my optical drives. ... The power supply is a brand new ... Control Panel - System - Hardware then this isn't an issue and I would look ...
      (microsoft.public.windowsxp.hardware)
    • Re: Workflow - deliverables
      ... " Otherwise you need to power the HD external. ... why would you put a Hub in between? ... When the sound editing team comes in they have either the 50 ... soon as I start another film I start over writing those drives. ...
      (rec.arts.movies.production.sound)
    • Re: HD is clicking
      ... >> Sometimes the HD starts to generate sound like click, click, and clik. ... > the noise, leaving the power cable attached. ... In my experience with hundreds of hard drives, a "click, click, clicking" ...
      (microsoft.public.windowsxp.hardware)
    • Re: Planning on building 1st computer
      ... The only thing I'd caution you about is, if it comes with a power supply, ... Plan to spend an entire weekend on assembly, prior to OS install. ... SATA drives are pretty fast. ... Check spacing of mainboard standoffs in case (must match all mounting ...
      (alt.comp.hardware.pc-homebuilt)
    • Re: NAS appliance or home server
      ... linux based -- that lurk around here. ... As far as power consumption goes: ... It has two 3.5" hard drives, so I'd budget 10W per drive. ... server side, and would also be able to set up a VCS server. ...
      (uk.comp.os.linux)