Boot Time hang with Promise Controller

From: Rik (rikb_at_corihemazoo.org)
Date: 09/28/03

Next message: Brett Glass: "Re: Recap of stable/4.9 status, please?"

Previous message: Mark Knight: "Re: strange problem with: ed driver / 4.9-PRE"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Date: Sat, 27 Sep 2003 17:39:30 -0600
To: freebsd-stable@freebsd.org

I am having a problem booting with 4.9 prerelease kernel.

The boot just stops and hangs the machine needing a reset to clear.

I include a dmesg from a kernel built Sept 7 that works and I indicate
where the boot stops on the kernel built today. (Sept 27)

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
reserved.
FreeBSD 4.9-PRERELEASE #37: Sun Sep 7 11:55:20 MDT 2003
    root@leopard.felines.net:/usr/obj/usr/src/sys/LEOPARD
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (551.25-MHz 686-class CPU)
  Origin = "GenuineIntel" Id = 0x673 Stepping = 3
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PA
T,PSE36,MMX,FXSR,SSE>
real memory = 268369920 (262080K bytes)
avail memory = 256663552 (250648K bytes)
Preloaded elf kernel "kernel.works" at 0xc0462000.
VESA: v3.0, 65536k memory, flags:0x1, mode table:0xc03d8782 (1000022)
VESA: NVidia
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 6 entries at 0xc00fdd30
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem
0xe8000000-0xebffffff at d
evice 0.0 on pci0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
pci1: <NVidia model 0110 graphics accelerator> at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xa000-0xa01f irq
10 at de
vice 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
intpm0: <Intel 82371AB Power management controller> port 0x5000-0x500f
irq 9 at
device 7.3 on pci0
intpm0: I/O mapped 5000
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped 4000
pcm0: <Creative EMU10K1> port 0xa400-0xa41f irq 11 at device 9.0 on pci0
pcm0: <TriTech TR28602 AC97 Codec>
atapci1: <Promise ATA66 controller> port
0xbc00-0xbc3f,0xb800-0xb803,0xb400-0xb4
07,0xb000-0xb003,0xac00-0xac07 mem 0xf0000000-0xf001ffff irq 5 at device
10.0 on
pci0
ata2: at 0xac00 on atapci1
ata3: at 0xb400 on atapci1
ahc0: <Adaptec 2930CU SCSI adapter> port 0xc000-0xc0ff mem
0xf0020000-0xf0020fff
irq 3 at device 11.0 on pci0
aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
rl0: <D-Link DFE-530TX+ 10/100BaseTX> port 0xc400-0xc4ff mem
0xf0021000-0xf00210
ff irq 10 at device 12.0 on pci0
rl0: Ethernet address: 00:05:5d:cf:b5:d8
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xd0000-0xd1fff,0xd2000-0xd27ff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
IPv6 packet filtering initialized, logging limited to 100 packets/entry
ipfw2 initialized, divert enabled, rule-based forwarding enabled,
default to den
y, logging limited to 100 packets/entry by default
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem
0xe8000000-0xebffffff at d
evice 0.0 on pci0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
pci1: <NVidia model 0110 graphics accelerator> at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xa000-0xa01f irq
10 at de
vice 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
intpm0: <Intel 82371AB Power management controller> port 0x5000-0x500f
irq 9 at
device 7.3 on pci0
intpm0: I/O mapped 5000
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped 4000
pcm0: <Creative EMU10K1> port 0xa400-0xa41f irq 11 at device 9.0 on pci0
pcm0: <TriTech TR28602 AC97 Codec>
atapci1: <Promise ATA66 controller> port
0xbc00-0xbc3f,0xb800-0xb803,0xb400-0xb4
07,0xb000-0xb003,0xac00-0xac07 mem 0xf0000000-0xf001ffff irq 5 at device
10.0 on
pci0

The kernel built today stops here and doesn't proceed.

ata2: at 0xac00 on atapci1
ata3: at 0xb400 on atapci1
ahc0: <Adaptec 2930CU SCSI adapter> port 0xc000-0xc0ff mem
0xf0020000-0xf0020fff
irq 3 at device 11.0 on pci0
aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
rl0: <D-Link DFE-530TX+ 10/100BaseTX> port 0xc400-0xc4ff mem
0xf0021000-0xf00210
ff irq 10 at device 12.0 on pci0
rl0: Ethernet address: 00:05:5d:cf:b5:d8
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xd0000-0xd1fff,0xd2000-0xd27ff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
IPv6 packet filtering initialized, logging limited to 100 packets/entry
ipfw2 initialized, divert enabled, rule-based forwarding enabled,
default to den
y, logging limited to 100 packets/entry by default
DUMMYNET initialized (011031)
IPsec: Initialized Security Association Processing.
ad0: 3079MB <QUANTUM FIREBALL SE3.2A> [6256/16/63] at ata0-master UDMA33
ad4: 29311MB <Maxtor 53073H6> [59554/16/63] at ata2-master UDMA66
ad6: 19595MB <QUANTUM FIREBALLP LM20.5> [39813/16/63] at ata3-master
UDMA66
acd0: CDROM <CREATIVE CD5233E> at ata1-master PIO4
Waiting 8 seconds for SCSI devices to settle
Mounting root from ufs:/dev/ad6s1a
cd0 at ahc0 bus 0 target 2 lun 0
cd0: <YAMAHA CRW8824S 1.00> Removable CD-ROM SCSI-2 device
cd0: 20.000MB/s transfers (20.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present
- tray c
losed
da0 at ahc0 bus 0 target 5 lun 0
da0: <IOMEGA ZIP 250 H.41> Removable Direct Access SCSI-2 device
da0: 3.300MB/s transfers
da0: 239MB (489532 512 byte sectors: 64H 32S/T 239C)
nvidia0: <GeForce2 MX/MX 400> mem
0xe0000000-0xe7ffffff,0xec000000-0xecffffff ir
q 11 at device 0.0 on pci1

_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"

Next message: Brett Glass: "Re: Recap of stable/4.9 status, please?"

Previous message: Mark Knight: "Re: strange problem with: ed driver / 4.9-PRE"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Relevant Pages

Fwd: MFS and Kernel panics (5.0-RELEASE-p7)
... BTW- I found this "problem" while playing with a PicoBSD build of the kernel. ... pci0: <PCI bus> on pcib0 ... pci_cfgintr: 0:10 INTA routed to irq 11 ... can't assign resources (port) ...
(freebsd-questions)
Diagnosing hardware issue?
... installing FreeBSD, I have encountered a number of problems I have no ... kernel without any noticeable errors. ... pci0: <PCI bus> on pcib0 ...
(freebsd-stable)
ATA problems(unlean fs) on recent cvsup
... pci0: <ACPI PCI bus> on pcib0 ... pcib0: slot 2 INTA is routed to irq 11 ...
(freebsd-current)
Fwd: Re: em0 problems on t41 after updating to 5.3
... acpi0: on motherboard ... pci0: <ACPI PCI bus> on pcib0 ... 0xc0100000-0xc010ffff,0xe0000000-0xe7ffffff irq 11 at device 0.0 on ...
(freebsd-questions)
panic and fs corruption in -current
... I compiled yesterday's kernel without problems, ... pci0: ... irq 16 at device 27.0 on pci0 ... 2 ports with 2 removable, ...
(freebsd-current)