Re: USB2 device

From: Michael E. Mercer (mmercer_at_nc.rr.com)
Date: 03/30/04

  • Next message: Julian Elischer: "Re: USB2 device" 
    To: Julian Elischer <julian@elischer.org>
Date: Mon, 29 Mar 2004 18:31:40 -0500

    Julian,

    I built the kernel with ehci, it boots and I see another hub using ehci.
    However when I plug in my JumpDrive, it does not get added.

    Michael Mercer

    Copyright (c) 1992-2003 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
            The Regents of the University of California. All rights reserved.
    FreeBSD 4.9-STABLE #0: Mon Mar 29 18:19:39 EST 2004
        mmercer@fast.mmercer.com:/usr/obj/usr/src/sys/g49
    Timecounter "i8254" frequency 1193182 Hz
    CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3006.83-MHz 686-class CPU)
      Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
     
    Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
      Hyperthreading: 2 logical CPUs
    real memory = 1072889856 (1047744K bytes)
    avail memory = 1039880192 (1015508K bytes)
    Programming 24 pins in IOAPIC #0
    IOAPIC #0 intpin 2 -> irq 0
    IOAPIC #0 intpin 17 -> irq 10
    IOAPIC #0 intpin 18 -> irq 5
    IOAPIC #0 intpin 19 -> irq 11
    FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs
     cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000
     cpu1 (AP): apic id: 1, version: 0x00050014, at 0xfee00000
     io0 (APIC): apic id: 2, version: 0x00178020, at 0xfec00000
    Preloaded elf kernel "kernel" at 0xc042b000.
    Warning: Pentium 4 CPU: PSE disabled
    Pentium Pro MTRR support enabled
    md0: Malloc disk
    Using $PIR table, 12 entries at 0xc00f50e0
    apm0: <APM BIOS> on motherboard
    apm0: found APM BIOS v1.2, connected at v1.2
    npx0: <math processor> on motherboard
    npx0: INT 16 interface
    pcib0: <Host to PCI bridge> on motherboard
    pci0: <PCI bus> on pcib0
    agp0: <Intel 82875P host to AGP bridge> mem 0xd0000000-0xdfffffff at
    device 0.0 on pci0
    pcib1: <PCI to PCI bridge (vendor=8086 device=2579)> at device 1.0 on
    pci0
    pci1: <PCI bus> on pcib1
    pci1: <NVidia model 0322 graphics accelerator> at 0.0 irq 10
    pcib2: <PCI to PCI bridge (vendor=8086 device=257b)> at device 3.0 on
    pci0
    pci2: <PCI bus> on pcib2
    em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port
    0xcf80-0xcf9f mem 0xfe9e0000-0xfe9fffff irq 5 at device 1.0 on pci2
    em0: Speed:N/A Duplex:N/A
    uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xef00-0xef1f
    irq 10 at device 29.0 on pci0
    usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
    usb0: USB revision 1.0
    uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub0: 2 ports with 2 removable, self powered
    uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xef20-0xef3f
    irq 11 at device 29.1 on pci0
    usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
    usb1: USB revision 1.0
    uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub1: 2 ports with 2 removable, self powered
    uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xef40-0xef5f
    irq 5 at device 29.2 on pci0
    usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
    usb2: USB revision 1.0
    uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub2: 2 ports with 2 removable, self powered
    uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xef80-0xef9f
    irq 10 at device 29.3 on pci0
    usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
    usb3: USB revision 1.0
    uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub3: 2 ports with 2 removable, self powered
    ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfebffc00-0xfebfffff irq
    11 at device 29.7 on pci0
    ehci_pci_attach: companion usb0
    ehci_pci_attach: companion usb1
    ehci_pci_attach: companion usb2
    ehci_pci_attach: companion usb3
    usb4: EHCI version 1.0
    usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
    usb4: <EHCI (generic) USB 2.0 controller> on ehci0
    usb4: USB revision 2.0
    uhub4: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
    uhub4: 8 ports with 8 removable, self powered
    uhub5: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00,
    addr 2
    uhub5: 4 ports with 4 removable, self powered
    uhub5: cannot open interrupt pipe
    device_probe_and_attach: uhub5 attach returned 6
    uhub5: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00,
    addr 2
    uhub5: 4 ports with 4 removable, self powered
    uhub5: cannot open interrupt pipe
    device_probe_and_attach: uhub5 attach returned 6
    pcib3: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on
    pci0
    pci3: <PCI bus> on pcib3
    fwohci0: <VIA VT6306> port 0xdc00-0xdc7f mem 0xfeaff800-0xfeafffff irq 5
    at device 3.0 on pci3
    fwohci0: OHCI version 1.0 (ROM=1)
    fwohci0: No. of Isochronous channel is 8.
    fwohci0: EUI64 00:e0:18:00:00:58:2a:e6
    fwohci0: Phy 1394a available S400, 3 ports.
    fwohci0: Link S400, max_rec 2048 bytes.
    firewire0: <IEEE1394(FireWire) bus> on fwohci0
    fwe0: <Ethernet over FireWire> on firewire0
    if_fwe0: Fake Ethernet address: 02:e0:18:58:2a:e6
    fwohci0: Initiate bus reset
    fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
    firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
    firewire0: bus manager 0 (me)
    isab0: <PCI to ISA bridge (vendor=8086 device=24d0)> at device 31.0 on
    pci0
    isa0: <ISA bus> on isab0
    atapci0: <Intel ICH5 ATA100 controller> port
    0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
    ata0: at 0x1f0 irq 14 on atapci0
    ata1: at 0x170 irq 15 on atapci0
    pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 10
    pcm0: <Intel ICH5 (82801EB)> port 0xee80-0xeebf,0xe800-0xe8ff mem
    0xfebff400-0xfebff4ff,0xfebff800-0xfebff9ff irq 10 at device 31.5 on
    pci0
    pcm0: <Analog Devices AD1985 AC97 Codec>
    orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0
    pmtimer0 on isa0
    fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
    isa0
    fdc0: FIFO enabled, 8 bytes threshold
    fd0: <1440-KB 3.5" drive> on fdc0 drive 0
    atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
    atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
    kbd0 at atkbd0
    psm0: <PS/2 Mouse> irq 12 on atkbdc0
    psm0: model IntelliMouse Explorer, device ID 4
    vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
    isa0
    sc0: <System console> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sio0: configured irq 4 not in bitmap of probed irqs 0
    sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
    sio0: type 16550A
    sio1: configured irq 3 not in bitmap of probed irqs 0
    sio1 at port 0x2f8-0x2ff irq 3 on isa0
    sio1: type 16550A
    ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
    ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
    ppc0: FIFO with 16/16/9 bytes threshold
    plip0: <PLIP network interface> on ppbus0
    lpt0: <Printer> on ppbus0
    lpt0: Interrupt-driven port
    ppi0: <Parallel I/O> on ppbus0
    APIC_IO: Testing 8254 interrupt delivery
    APIC_IO: routing 8254 via IOAPIC #0 intpin 2
    SMP: AP CPU #1 Launched!
    ad0: 39205MB <Maxtor 6E040L0> [79656/16/63] at ata0-master UDMA100
    ad3: 194481MB <Maxtor 6Y200P0> [395136/16/63] at ata1-slave UDMA100
    acd0: DVD-R <OPTORITEDVD RW DD0203> at ata1-master PIO4
    Mounting root from ufs:/dev/ad3s1a
    em0: Link is up 100 Mbps Full Duplex
    em0: Link is up 100 Mbps Full Duplex

    _______________________________________________
    freebsd-stable@freebsd.org mailing list
    http://lists.freebsd.org/mailman/listinfo/freebsd-stable
    To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"

  • Next message: Julian Elischer: "Re: USB2 device"

    Relevant Pages