3ware 9500S problem in newly updated 4.x box.
From: Jason Thomson (jason.thomson_at_mintel.com)
Date: 01/26/05
- Previous message: Oliver Fromme: "Re: Use loader to load kernel.gz and mfsroot.gz in ext2 filesystem?"
- Next in thread: Vinod Kashyap: "RE: 3ware 9500S problem in newly updated 4.x box."
- Maybe reply: Vinod Kashyap: "RE: 3ware 9500S problem in newly updated 4.x box."
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Wed, 26 Jan 2005 15:51:59 +0000 To: freebsd-stable@freebsd.org
Recently CVSupped and rebuilt a releng4 box.
This box has a 9500S in RAID10 configuration.
On reboot, it failed to find da0, so it couldn't mount root.
If you wait a few seconds, and then type to specify the root filesystem
again, then the da0 device is found (the message is printed as you
type), and on hitting return, the machine continues booting.
(See dmesg below).
The twa driver and firmware are up to date.
This is a DELL 1600SC SMP. HyperThreading is enabled (but it's not a
big deal to us one way or the other, so if it's a good idea to turn it
off, we could).
If you don't type on the keyboard, then the message doesn't appear. I
haven't tried this without SMP. It's a production box I just upgraded,
and can only mess around with it early in the morning.
Before today, it was running FreeBSD 4-STABLE from September 24th.
Has anyone else seen this? Does anyone have any ideas? Is there
anything I can try to debug this?
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.11-STABLE #3: Wed Jan 26 14:03:18 GMT 2005
jason@baldrick.mintel.co.uk:/usr/obj/usr/src/sys/BALDRICK
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2790.72-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 3757965312 (3669888K bytes)
avail memory = 3659362304 (3573596K bytes)
Changing APIC ID for IO APIC #0 from 0 to 8 on chip
Changing APIC ID for IO APIC #1 from 0 to 9 on chip
Changing APIC ID for IO APIC #2 from 0 to 10 on chip
Programming 16 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 16 pins in IOAPIC #1
Programming 16 pins in IOAPIC #2
FreeBSD/SMP: Multiprocessor motherboard: 4 CPUs
cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00050014, at 0xfee00000
cpu2 (AP): apic id: 6, version: 0x00050014, at 0xfee00000
cpu3 (AP): apic id: 7, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id: 8, version: 0x000f0011, at 0xfec00000
io1 (APIC): apic id: 9, version: 0x000f0011, at 0xfec01000
io2 (APIC): apic id: 10, version: 0x000f0011, at 0xfec02000
pnpbios: Bad PnP BIOS data checksum
Preloaded elf kernel "kernel" at 0xa03f0000.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 9 entries at 0xa00fc200
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
IOAPIC #1 intpin 0 -> irq 2
IOAPIC #1 intpin 9 -> irq 3
pci0: <PCI bus> on pcib0
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port
0xecc0-0xecff mem 0xfe100000-0xfe11ffff irq 2 at device 2.0 on pci0
em0: Speed:N/A Duplex:N/A
sis0: <NatSemi DP83815 10/100BaseTX> port 0xe800-0xe8ff mem
0xfe122000-0xfe122fff irq 3 at device 4.0 on pci0
sis0: Ethernet address: 00:02:e3:02:6e:10
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <ATI Mach64-GR graphics accelerator> at 14.0
atapci0: <ServerWorks CSB5 ATA100 controller> port
0x8b0-0x8bf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device
15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <OHCI USB controller> at 15.2 irq 5
isab0: <PCI to ISA bridge (vendor=1166 device=0225)> at device 15.3 on pci0
isa0: <ISA bus> on isab0
pcib1: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
IOAPIC #1 intpin 4 -> irq 10
pci1: <PCI bus> on pcib1
3ware device driver for 9000 series storage controllers, version:
2.40.02.011
twa0: <3ware 9000 series Storage Controller> port 0xdc00-0xdcff mem
0xfc000000-0xfc7fffff,0xfcf00000-0xfcf000ff irq 10 at device 6.0 on pci1
twa0: 4 ports, Firmware FE9X 2.04.00.005, BIOS BE9X 2.03.01.047
pcib2: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib2
pcib3: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci3: <PCI bus> on pcib3
pcib4: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci4: <PCI bus> on pcib4
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc97ff,0xe3000-0xea7ff,0xec000-0xeffff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0
intpin 2
APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0
IP packet filtering initialized, divert enabled, rule-based forwarding
enabled, default to deny, logging limited to 1000 packets/entry by default
IPsec: Initialized Security Association Processing.
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
acd0: CDROM <SAMSUNG CD-ROM SC-148A> at ata1-master PIO4
Mounting root from ufs:/dev/da0s1a
no such device 'da'
setrootbyname failed
ffs_mountroot: can't find rootvp
Root mount failed: 6
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:/dev/da0s1a
? List valid disk boot devices
<empty line> Abort manual input
mountroot> ufs\^[[}\^[[}:/dev/da0s1a
Mounting root from ufs\^[[}\^[[}:/dev/da0s1a
ffs_mountroot: can't find rootvp
Root mount failed: 6
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:/dev/da0s1a
? List valid disk boot devices
<empty line> Abort manual input
mountroot> da0 at twa0 bus 0 target 0 lun 0
da0: <3ware Logical Disk 00 1.00> Fixed Direct Access SCSI-0 device
da0: 100.000MB/s transfers
da0: 381448MB (781205504 512 byte sectors: 255H 63S/T 48627C)
ufs:/dev/da0s1a
Mounting root from ufs:/dev/da0s1a
ohci0: <OHCI (generic) USB controller> mem 0xfe120000-0xfe120fff irq 5
at device 15.2 on pci0
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
em0: Link is up 100 Mbps Full Duplex
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"
- Previous message: Oliver Fromme: "Re: Use loader to load kernel.gz and mfsroot.gz in ext2 filesystem?"
- Next in thread: Vinod Kashyap: "RE: 3ware 9500S problem in newly updated 4.x box."
- Maybe reply: Vinod Kashyap: "RE: 3ware 9500S problem in newly updated 4.x box."
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
