Re: [SOLVED] VIA M1000 mini-itx system installation woes - WRITE_DMA error
From: W C (woodycarey_at_hotmail.com)
Date: 04/28/05
- Previous message: Joe Altman: "Re: USB changes."
- In reply to: Arjan Van Leeuwen: "Re: VIA M1000 mini-itx system installation woes - WRITE_DMA error - cabling?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
To: avleeuwen@gmail.com Date: Thu, 28 Apr 2005 13:20:59 -0700
This solution worked like a charm! Thanks Arjan!
One note: use "set ..." syntax in the interactive loader prompt (6), and
use
"hw.ata.ata_dma="0" *without* "set " in /boot/loader.conf
Interestingly, setting the drive in the BIOS to PIO4 mode had no effect.
Now if I can just get carrier on my vr0 interface, I won't have to return
this system!
Woody
>From: Arjan Van Leeuwen <avleeuwen@gmail.com>
>Reply-To: Arjan Van Leeuwen <avleeuwen@gmail.com>
>To: W C <woodycarey@hotmail.com>
>CC: freebsd-stable@freebsd.org
>Subject: Re: VIA M1000 mini-itx system installation woes - WRITE_DMA error
>-cabling?
>Date: Wed, 27 Apr 2005 10:11:16 +0200
>
>On 4/26/05, W C <woodycarey@hotmail.com> wrote:
> > Hi all,
> >
> > I am attempting to install 5.3-R from cd (iso image download) and
> > sysinstall is failing
> > to write the chosen (Auto Layout) filesystem to disk, the Toshiba 80G on
>the
> > primary ide channel as master. The error on vty1 is (from memory) ad0:
> > WRITE_DMA, error=84.
> > The drive is detected by BIOS as a UDMA100 device. There is nothing
>else on
> > this IDE channel, and only a cd drive on the other IDE slot.
> >
> > A search of -questions reveals this error is a UDMA mismatch, possible
> > caused by 80-pin cabling, and fixable with atacontrol ad0 udma33 pio bla
>bla
> > bla. However, I do not yet have a running system to run atacontrol
>from, as
> > I am installing. I have rooted around in the bios for an option to
>force
> > the drive to UDMA33 speed, to no avail. Does anyone know how I can work
> > around this problem and install FreeBSD to this neat little system? Do
>I
> > have bad cabling, a bad drive, or ???
>
>Yes, I had the same problem.
>
>If this is a 2.5" drive, it probably doesn't have a 80-pins cable.
>Force PIO mode for the install by entering at the boot prompt (option
>6 in the boot loader menu):
> set hw.ata.ata_dma="0"
> boot
>
>After you've installed the system, insert that line into
>/boot/loader.conf, and load up "atacontrol mode 0 udma33 udma33" as
>early as possible during the boot (try using /etc/rc.early, for
>example) to get it up to speed again.
>
>Arjan
>_______________________________________________
>freebsd-stable@freebsd.org mailing list
>http://lists.freebsd.org/mailman/listinfo/freebsd-stable
>To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"
_________________________________________________________________
On the road to retirement? Check out MSN Life Events for advice on how to
get there! http://lifeevents.msn.com/category.aspx?cid=Retirement
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"
- Previous message: Joe Altman: "Re: USB changes."
- In reply to: Arjan Van Leeuwen: "Re: VIA M1000 mini-itx system installation woes - WRITE_DMA error - cabling?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
