Re: DELL PowerEdge 2850 and FreeBSD 5.4

From: David Barnett (davidb_at_santacruz.k12.ca.us)
Date: 06/02/05

  • Next message: Dick Davies: "Re: filesystems not properly unmounted" 
    Date: Thu, 02 Jun 2005 09:52:25 -0700
To: Gary Schrock <lists@eyelab.psy.msu.edu>

    Gary,

    I'm fighting the same battle on two new 2850's and two 1850's; "Interrupt
    storm detected on "irq18:uhci2"; throttling interrupt source".

    These machines have 2GB of ram and I using the i386 5.4Rel. version.
    This happens
    right after the reboot at the end of an install from CD. I've chosen to
    install "all",
    and bring up the ethernet interface. When I get the message, the
    machine is unresponsive
    to keyboard input or pings; basically frozen. I also tried 5.3 Rel.
    with the same results.

     From searching the lists I concluded disabling USB might be worth
    trying, so I did that
    in the BIOS. I'm still getting the same message and freeze.

    How are you disabling USB? It seems that has worked for you.

    One tidbit, they have the DRAC 4/I remote access controller cards in
    them, but I have no
    reason to believe they're involved at this point. Oh, and firmware is
    current throughout.

    Thanks for any hints.

    Dave Barnett

    Gary Schrock wrote:

    > At 05:05 AM 6/1/2005, you wrote:
    >
    >> I have checked on the DELL site for any updates to the BIOS/Firmware
    >> and the
    >> 2 PE2850's are running the latest versions.
    >>
    >> BIOS A02
    >> Dell Backplane Firmware, v.1.00, A00
    >> Dell BMC Firmware, v.1.23, A03
    >> LSI Logic Perc 4e/Di, v.516A, A01
    >>
    >> Both machines have the same symptoms or the reboots at random times.
    >>
    >> I have now disabled the USB via rc.conf to see if the reboots still
    >> occur.
    >> On one machine I shall drop the PAE kernel and see if that increases the
    >> stability
    >
    >
    > We've been running a 2850 with dual processors for a while now,
    > although we're only running 2G of ram. I'm also running the i386
    > verson of freebsd instead of amd64 (since I couldn't decide whether
    > I'd really gain anything by running that version, especially with my
    > low ram amount). We did initially have a problem with our add-on
    > perc4 controller, but that was obviously a problem with that
    > controller, but after that was resolved, the only issue I've had with
    > it is the usb interrupt storms. Since we don't use usb on that
    > system, I've just completely disabled it. After that, it's run
    > flawlessly for about 6 months now.
    >
    >> Regards
    >>
    >> Danny
    >>
    >> -----Original Message-----
    >> From: owner-freebsd-stable@freebsd.org
    >> [mailto:owner-freebsd-stable@freebsd.org] On Behalf Of Vinny Abello
    >> Sent: 01 June 2005 05:10
    >> To: Danny Cooper
    >> Cc: freebsd-stable@freebsd.org
    >> Subject: RE: DELL PowerEdge 2850 and FreeBSD 5.4
    >>
    >> What BIOS revision are you running in your 2850? Make sure all your
    >> firmware is up to date. I had problems with an slightly older Dell
    >> 2650 trying to install FreeBSD until I flashed the latest RAID
    >> controller firmware. If this doesn't help, try running some
    >> diagnostics on the hardware. Dell has some pretty extensive
    >> utilities. I think you can boot a Dell diagnostic CD you download
    >> from their web site. It's possible you have bad RAM.
    >>
    >> At 11:50 AM 5/31/2005, Danny Cooper wrote:
    >> >With the kernel I removed all non-required devices
    >> >
    >> >Firewire, usb all the NIC's except em and removed all RAID and SCSI
    >> >controllers to make sure nothing would interfere.
    >> >
    >> >I tried to boot with the AMD64 CD but with no success, the machine just
    >> >hangs when it tries to load the CD, still trying to work out a
    >> solution to
    >> >the problem, but it just seems these DELL 2850 machines are for
    >> Windows or
    >> >RedHat!!!
    >> >
    >> >DC
    >> >
    >> >-----Original Message-----
    >> >From: owner-freebsd-stable@freebsd.org
    >> >[mailto:owner-freebsd-stable@freebsd.org] On Behalf Of Claus Guttesen
    >> >Sent: 31 May 2005 16:15
    >> >To: Danny Cooper
    >> >Cc: freebsd-stable@freebsd.org
    >> >Subject: Re: DELL PowerEdge 2850 and FreeBSD 5.4
    >> >
    >> > > I have installed FreeBSD 5.4 RELEASE and upgraded to -STABLE on a
    >> DELL
    >> > > PE2850.
    >> > >
    >> > > FreeBSD 5.4-STABLE #1: Wed May 25 23:43:12 BST 2005
    >> > > CPU: Intel(R) Xeon(TM) CPU 3.20GHz (3192.22-MHz 686-class CPU)
    >> > > real memory = 5100273664 (4864 MB)
    >> > > avail memory = 4189892608 (3995 MB)
    >> > > MPTable: <DELL PE 016D >
    >> > > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
    >> > > cpu0 (BSP): APIC ID: 0
    >> > > cpu1 (AP): APIC ID: 6
    >> > > amr0: <LSILogic PERC 4e/Di> Firmware 516A, BIOS H418, 256MB RAM
    >> > >
    >> > > I have disabled ACPI HTT and enabled PAE to make the whole system
    >> memory
    >> > > available.
    >> > >
    >> > > However the problem I have is the system can crash at any moment,
    >> and is
    >> >not
    >> > > load related. As the crash info below is when the machine was in
    >> an 100%
    >> > > idle state.
    >> >
    >> >I have the same hardware as well, running on the i386-port. I have
    >> >disabled usb with usbd_enable="NO" in /etc/rc.conf. I have no idea
    >> >whether this helps but havent't had an issue with the 2850. Except
    >> >with a qlogic-hba and the isp-driver (I suspect) *on* amd64, but *not*
    >> >on i386.
    >> >
    >> >Claus
    >> >_______________________________________________
    >> >freebsd-stable@freebsd.org mailing list
    >> >http://lists.freebsd.org/mailman/listinfo/freebsd-stable
    >> >To unsubscribe, send any mail to
    >> "freebsd-stable-unsubscribe@freebsd.org"
    >> >
    >> >
    >> >_______________________________________________
    >> >freebsd-stable@freebsd.org mailing list
    >> >http://lists.freebsd.org/mailman/listinfo/freebsd-stable
    >> >To unsubscribe, send any mail to
    >> "freebsd-stable-unsubscribe@freebsd.org"
    >>
    >>
    >> Vinny Abello
    >> Network Engineer
    >> Server Management
    >> vinny@tellurian.com
    >> (973)300-9211 x 125
    >> (973)940-6125 (Direct)
    >> PGP Key Fingerprint: 3BC5 9A48 FC78 03D3 82E0 E935 5325 FBCB 0100 977A
    >>
    >> Tellurian Networks - The Ultimate Internet Connection
    >> http://www.tellurian.com (888)TELLURIAN
    >>
    >> "Courage is resistance to fear, mastery of fear - not absence of
    >> fear" -- Mark Twain
    >>
    >>
    >> _______________________________________________
    >> freebsd-stable@freebsd.org mailing list
    >> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
    >> To unsubscribe, send any mail to
    >> "freebsd-stable-unsubscribe@freebsd.org"
    >>
    >>
    >> _______________________________________________
    >> freebsd-stable@freebsd.org mailing list
    >> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
    >> To unsubscribe, send any mail to
    >> "freebsd-stable-unsubscribe@freebsd.org"
    >
    >
    > _______________________________________________
    > freebsd-stable@freebsd.org mailing list
    > http://lists.freebsd.org/mailman/listinfo/freebsd-stable
    > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"

    _______________________________________________
    freebsd-stable@freebsd.org mailing list
    http://lists.freebsd.org/mailman/listinfo/freebsd-stable
    To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"

  • Next message: Dick Davies: "Re: filesystems not properly unmounted"

    Relevant Pages

    • Re: usb ports not working in xp pro
      ... Tha computer was bought new from dell, and belongs to my golf club. ... They have had dell technician out who replaced the mobo and usb ports, ... You could try a repair install. ... and the USB ports would come off that. ...
      (microsoft.public.windowsxp.hardware)
    • Re: OS wont boot
      ... have a usb 'thumb drive' plugged in for instanance it is possible that the ... After the splash screen, The CD-rom ... original Dell XP disk wont work because of the upgrade to SP2). ... install drivers for the hard drive and then XP would recognize the C ...
      (alt.sys.pc-clone.dell)
    • Re: ERROR MESSAGE ON BLUE SCREEN
      ... are childrens games tried to install freecom cd for dvd rw with roxio on this ... Your BIOS probably would benefit from a BIOS upgrade but it would not ... We are looking to find an updated driver for a USB ... Were these bought with the Dell or later? ...
      (microsoft.public.windowsxp.help_and_support)
    • Re: Windows wont start with USB printer plugged in
      ... In one case it is a Dell Computer with an HP printer. ... If you remove the printer USB cable, ... then the computer go to the BIOS splash screen. ... Then I took it to the owners home and install her Epson ...
      (microsoft.public.windowsxp.general)
    • Re: Installing an HP Photosmart 7150 Printer
      ... Did you also remember to turn the printer on after connecting it to the USB ... Is it the same USB port you installed the Dell (actually a rebadged ... Cari Windows Client - Printing/Imaging and Hardware ... We are trying to install an HP Photosmart 7150 ...
      (microsoft.public.windowsxp.help_and_support)