burncd input output error

From: Andreas Klemm (andreas_at_klemm.apsfilter.org)
Date: 09/17/05

  • Next message: Scott Robbins: "Re: burncd input output error" 
    Date: Sat, 17 Sep 2005 15:03:44 +0200
To: freebsd-stable@freebsd.org

    2 problems with FreeBSD 5.4 stable:

    - burncd has strange exit status when reading ISO file from stdin
      according to manual page possible:
       [...]
       gunzip -c file.iso.gz | burncd -f /dev/acd0 data - fixate
       [...]

    - burncd leaves cdrom in a way that CD cannot be mounted
      after burning, one has to open and re-close CD tray manually
      before one is able to mount the frshly burned CD.

    *** trying to burn ISO file

    root# rtprio 5 bzcat myfile.iso.bz2 \
            | rtprio 5 burncd -s max -f /dev/acd1 data - fixate
    next writeable LBA 0
    writing from stdin
    written this track 224678 KB total 224678 KB
    fixating CD, please wait..
    burncd: ioctl(CDRIOCFIXATE): Input/output error
    Exitcode 74

    *** trying to mount cdrom

    root# mount -r -t cd9660 /dev/acd1 /cdrom
    cd9660: /dev/acd1: Input/output error
    Exit 1

    *** ejecting cdrom manually and retrying mount operation

    root# mount -r -t cd9660 /dev/acd1 /cdrom
    root# cd /cdrom
    root# ll
    total 21752
    -rw-r--r-- 2 root wheel 878 Sep 11 14:23 .cshrc
    -rw-r--r-- 2 root wheel 329 Sep 11 14:23 .profile
    -r--r--r-- 1 root wheel 6886 Sep 11 14:23 COPYRIGHT
    [...]

    *** dmesg output

    Copyright (c) 1992-2005 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
            The Regents of the University of California. All rights reserved.
    FreeBSD 5.4-STABLE #0: Mon Sep 12 20:43:56 CEST 2005
        root@titan.klemm.apsfilter.org:/usr/src/sys/amd64/compile/TITAN64
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: AMD Athlon(tm) 64 Processor 3000+ (1808.81-MHz K8-class CPU)
      Origin = "AuthenticAMD" Id = 0x10ff0 Stepping = 0
      Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
      AMD Features=0xe2500800<SYSCALL,NX,MMX+,<b25>,LM,3DNow+,3DNow>
    real memory = 1073676288 (1023 MB)
    avail memory = 1026531328 (978 MB)
    cpu0 on motherboard
    pcib0: <Host to PCI bridge> pcibus 0 on motherboard
    pci0: <PCI bus> on pcib0
    isab0: <PCI-ISA bridge> at device 1.0 on pci0
    isa0: <ISA bus> on isab0
    pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
    ohci0: <OHCI (generic) USB controller> mem 0xfc003000-0xfc003fff irq 7 at device 2.0 on pci0
    usb0: OHCI version 1.0, legacy support
    usb0: SMM does not respond, resetting
    usb0: <OHCI (generic) USB controller> on ohci0
    usb0: USB revision 1.0
    uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub0: 4 ports with 4 removable, self powered
    ohci1: <OHCI (generic) USB controller> mem 0xfc004000-0xfc004fff irq 7 at device 2.1 on pci0
    usb1: OHCI version 1.0, legacy support
    usb1: SMM does not respond, resetting
    usb1: <OHCI (generic) USB controller> on ohci1
    usb1: USB revision 1.0
    uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub1: 4 ports with 4 removable, self powered
    ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfc005000-0xfc0050ff irq 7 at device 2.2 on pci0
    usb2: EHCI version 1.0
    usb2: companion controllers, 4 ports each: usb0 usb1
    usb2: <EHCI (generic) USB 2.0 controller> on ehci0
    usb2: USB revision 2.0
    uhub2: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
    uhub2: 8 ports with 8 removable, self powered
    pci0: <bridge> at device 5.0 (no driver attached)
    pcm0: <nVidia nForce3 250> port 0xac00-0xac7f,0xa800-0xa8ff mem 0xfc001000-0xfc001fff irq 11 at device 6.0 on pci0
    pcm0: <Avance Logic ALC850 AC97 Codec>
    atapci0: <nVidia nForce3 Pro UDMA133 controller> port 0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 8.0 on pci0
    ata0: channel #0 on atapci0
    ata1: channel #1 on atapci0
    atapci1: <GENERIC ATA controller> port 0xc800-0xc80f,0xb60-0xb63,0x960-0x967,0xbe0-0xbe3,0x9e0-0x9e7 irq 10 at device 9.0 on pci0
    ata2: channel #0 on atapci1
    ata3: channel #1 on atapci1
    atapci2: <GENERIC ATA controller> port 0xe000-0xe00f,0xb70-0xb73,0x970-0x977,0xbf0-0xbf3,0x9f0-0x9f7 irq 11 at device 10.0 on pci0
    ata4: channel #0 on atapci2
    ata5: channel #1 on atapci2
    pcib1: <PCI-PCI bridge> at device 11.0 on pci0
    pci1: <PCI bus> on pcib1
    pci1: <display, VGA> at device 0.0 (no driver attached)
    pci1: <display> at device 0.1 (no driver attached)
    pcib2: <PCI-PCI bridge> at device 14.0 on pci0
    pci2: <PCI bus> on pcib2
    pci2: <multimedia, audio> at device 8.0 (no driver attached)
    fwohci0: <VIA Fire II (VT6306)> port 0x9000-0x907f mem 0xfb001000-0xfb0017ff irq 5 at device 12.0 on pci2
    fwohci0: OHCI version 1.0 (ROM=1)
    fwohci0: No. of Isochronous channels is 4.
    fwohci0: EUI64 00:10:dc:00:00:77:91:3e
    fwohci0: Phy 1394a available S400, 3 ports.
    fwohci0: Link S400, max_rec 2048 bytes.
    firewire0: <IEEE1394(FireWire) bus> on fwohci0
    fwe0: <Ethernet over FireWire> on firewire0
    if_fwe0: Fake Ethernet address: 02:10:dc:77:91:3e
    fwe0: Ethernet address: 02:10:dc:77:91:3e
    fwe0: if_start running deferred for Giant
    sbp0: <SBP-2/SCSI over FireWire> on firewire0
    fwohci0: Initiate bus reset
    fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
    firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
    firewire0: bus manager 0 (me)
    re0: <RealTek 8169S Single-chip Gigabit Ethernet> port 0x9400-0x94ff mem 0xfb000000-0xfb0000ff irq 5 at device 13.0 on pci2
    miibus0: <MII bus> on re0
    rgephy0: <RTL8169S/8110S media interface> on miibus0
    rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
    re0: Ethernet address: 00:11:09:cd:3e:59
    orm0: <ISA Option ROMs> at iomem 0xd6000-0xd6fff,0xd4000-0xd57ff,0xd0000-0xd3fff,0xc0000-0xccfff on isa0
    atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
    atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
    kbd0 at atkbd0
    psm0: <PS/2 Mouse> irq 12 on atkbdc0
    psm0: model IntelliMouse Explorer, device ID 4
    fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
    fd0: <1440-KB 3.5" drive> on fdc0 drive 0
    sc0: <System console> at flags 0x100 on isa0
    sc0: VGA <4 virtual consoles, flags=0x300>
    sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
    sio0: type 16550A
    sio1: configured irq 3 not in bitmap of probed irqs 0
    sio1: port may not be enabled
    vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ugen0: Syncrosoft Protected Executer, rev 1.10/1.01, addr 2
    Timecounter "TSC" frequency 1808811445 Hz quality 800
    Timecounters tick every 1.000 msec
    Fast IPsec: Initialized Security Association Processing.
    ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny, logging limited to 100 packets/entry by default
    acd0: DVDROM <LITEON DVD-ROM LTD122/IHNC> at ata1-master PIO4
    acd1: DVDR <HL-DT-ST DVDRAM GSA-4082B/A201> at ata1-slave PIO4
    ad4: 152627MB <ST3160827AS/3.42> [310101/16/63] at ata2-master UDMA33
    ad6: 152627MB <ST3160827AS/3.42> [310101/16/63] at ata3-master UDMA33
    cd0 at ata1 bus 0 target 0 lun 0
    cd0: <LITEON DVD-ROM LTD122 IHNC> Removable CD-ROM SCSI-0 device
    cd0: 16.000MB/s transfers
    cd0: Attempt to query device size failed: NOT READY, Medium not present
    cd1 at ata1 bus 0 target 1 lun 0
    cd1: <HL-DT-ST DVDRAM GSA-4082B A201> Removable CD-ROM SCSI-0 device
    cd1: 16.000MB/s transfers
    cd1: Attempt to query device size failed: NOT READY, Medium not present
    Mounting root from ufs:/dev/ad6s1a

            Andreas /// 

    -- 
http://www.64bits.de
http://www.apsfilter.org
http://people.FreeBSD.org/~andreas
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"
  • Next message: Scott Robbins: "Re: burncd input output error"

    Relevant Pages