Problems with AVM B1 PCMCIA (2nd try)

Hi folks,

the current FreeBSD STABLE version still has massive problems detecting my AVM
PCMCIA B1 active ISDN card. I am currently running 6.0-RELEASE-p5 and all that
it tells me is that the card it found "has no functions". I booted in verbose-
mode and enabled multiple debugging mechanisms and ended up with the following
messages in dmesg:

cbb0: <RF5C475 PCI-CardBus Bridge> irq 23 at device 11.0 on pci2
pcib2: cbb0 requested memory range 0xeb000000-0xed7fffff: good
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xeb001000
cbb0: Found memory at eb001000
cbb0: Secondary bus is 0
cbb0: Setting primary bus to 2
cbb0: Secondary bus set to 3 subbus 4
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0x04751180 0x02100007 0x06070081 0x00022000
0x10: 0xeb001000 0x020000dc 0x20040302 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x07000117
0x40: 0x00000000 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000001 0x00000000 0x04630463 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0xfe0a0001
0xe0: 0x24c04000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pci2: <network> at device 12.0 (no driver attached)
...
Status is 0x30000410
cbb0: card inserted: event=0x00000000, state=30000410
pccard0: chip_socket_enable
cbb_pcic_socket_enable:
cbb0: cbb_power: 5V
pccard0: read_cis
pcib2: pccard0 requested memory range 0xeb000000-0xed7fffff: good
cis mem map 0xe564e000 (resource: 0xeb010000)
pccard0: CIS tuple chain:
CISTPL_END
ff
cis mem map e564e000
CISTPL_LINKTARGET expected, code ff observed
pccard0: check_cis_quirks
pccard0: Card has no functions!
cbb0: PC Card card activation failed

Somebody please help me as I'm completely out of ideas ... please CC me when
replying, I am not subscribed to the freebsd-questions-mailinglist.

--
.''`. Martin Loschwitz Debian GNU/Linux developer
: :' : madkiss@xxxxxxxxxxx madkiss@xxxxxxxxxx
`. `'` http://www.madkiss.org/ people.debian.org/~madkiss/
`- Use Debian GNU/Linux 3.1! See http://www.debian.org/

Attachment: pgpyY1XSOat3k.pgp
Description: PGP signature

Relevant Pages

  • pccard0: Card has no functions!
    ... I have Nokia Card Phone 2.0 in a PCMCIA to PCI ... pccard0: chip_socket_enable ... cbb0: ... <ACPI PCI bus> on pcib0 ...
    (freebsd-hackers)
  • PC card problems in FreeBSD 5.2-RELEASE
    ... the solution is clearly PC cards or cardbus cards, ... Megahertz 56kglobal modem pc card and a Xircom CreditCard ... pccard0: on cbb0 ...
    (freebsd-questions)
  • apa-1460 Adaptec pccard
    ... Since a certain lot of time my scsi card doesn't work. ... Below is the result of the cis debug, ... pccard0: on cbb0 ...
    (freebsd-current)
  • FreeBSD CardBus
    ... cbb0: Found memory at fea00000 ... Secondary bus set to 4 subbus 5 ... cardbus0: <CardBus bus> on cbb0 ... Following that, no more messages (unless I remove the card and then reinsert it, but I never get any messages beyond this). ...
    (freebsd-questions)
  • Re: cardbus and xircom ethernet problem
    ... CISTPL_NONE 00 scrolling up the screen constantly until after 30 seconds ... or so it panics with page fault 12 in cbb0. ... : pccard0: Card has no functions! ... : cbb0: Card card activation failed ...
    (freebsd-current)