Re: 7.0-BETA4 and msk problems

On Mon, Dec 10, 2007 at 11:03:47AM +0200, Danny Braniss wrote:
> > On Sun, Dec 09, 2007 at 02:41:28PM +0200, Danny Braniss wrote:
> > > with this onboard NIC (LOB?)
> > >
> > > mskc0: <Marvell Yukon 88E8056 Gigabit Ethernet>
> > > e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus0
> > >
> > > mskc0@pci0:1:0:0: class=0x020000 card=0x81f81043 chip=0x436411ab
> > > rev=0x12 hdr=0x00
> > > vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)'
> > > device = '88E8056 Yukon PCI-E Gigabit Ethernet Controller'
> > > class = network
> > > subclass = ethernet
> > >
> > > I'm getting allot of:
> > > msk0: watchdog timeout
> > > and
> > > mskc0: Tx descriptor error
> > > and
> > > msk0: link state changed to DOWN
> > > and
> > > msk0: link state changed to UP
> > >
> > > any help is most welcome,
> > > danny
> > >
> > >
> >
> > It seems that the issue happens only on 88E8056/88E1149 PHY.
> > See PR 116853 and 114631.
> > Sorry, I have no cluet yet.
>
> to add some more noise, this is the first host that panicked too :-)
> anything I can do to help?

Probably ship the hardware to me? :)
love to, but the hardware is not mine :-)

here is some more info, this is a different board, but with the
same Marvell 88E8056, and it panics after printing 'no PHY found!'
and the ethernet is -1 (ff.ff...)

danny



_______________________________________________
freebsd-stable@xxxxxxxxxxx mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscribe@xxxxxxxxxxx"

Relevant Pages

  • Re: Microcontroller; any suggestions?
    ... and I want to use it on an Ethernet. ... recommended interface to, say, cat5? ... After the PHY comes 1:1 signaltransformer and various passive components. ... useing LVTTL I/O's. ...
    (sci.electronics.design)
  • Re: Ethernet chip - newbie need help with selection
    ... > Does making a PHY suggest a different semiconductor process? ... > certainly can be integrated with the rest of the ethernet functionality ... Read the MC9S12NE64 data sheet and note the lengths Freescale goes to ...
    (comp.arch.embedded)
  • AT91RM9200/Davicom and Altima phy compability
    ... 50Mhz and 25Mhz needed for a Davicom DM9161 PHY and a Davicom ... DM9000 10/100 ethernet controller. ... a better reliability on both of the ethernet circuits. ...
    (comp.arch.embedded)
  • Re: Ethernet network connection dead after reset til cable Unplug
    ... KITL (Kernel independant transport layer) often uses Ethernet as its transport layer - grep for 'OALKitlInit' in your tree to find the code. ... Put some code into the CheckForHangHandler to dump the PHY registers and Ethernet registers to see if you can fathom why it is stuck in the failure case. ... That seems like it is probably the expected thing, a software reset when the driver loads. ...
    (microsoft.public.windowsce.embedded)
  • ENC28j60 or CS8900A
    ... I have a microcontroller and I want to connect it to ... internet. ... At first I need a ethernet controller(MAC & PHY ethernet). ...
    (comp.arch.embedded)