[HPADM] Memory checksum Errors in rp2470
From: Joe Brancaleone (joe_at_nitech.com)
Date: 12/11/03
- Previous message: Naylor, Jim: "[HPADM] Insert characters in middle of line"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Wed, 10 Dec 2003 15:54:18 -0800 To: "Hpux-Admin@Dutchworks. Nl (E-mail)" <hpux-admin@dutchworks.nl>
Dear list,
I'm getting memory checksum errors while booting up an rp2470 server. The messages are below, which pop up on the console during the memory testing phase of POST (particularly after the "memory config 7214" lines). I can't seem to find any documentation explaining the reasons why I'd get "checksum errors" with memory that apparently works ok.
- Is this a critical error because of faulty memory modules? I tried switching around the modules but it did not change when the errors appear. (always comes after the 7214 lines)
- Or is this really a "non-critical" error because they are third-party modules? Installing and booting the OS went fine. The OS reported the correct amount of memory, etc.
Thanks in advance.
***** EARLY BOOT VFP : SYSTEM ALERT *****
SYSTEM NAME: unknown
DATE: 12/10/2003 TIME: 19:35:36
ALERT LEVEL: 6 = Boot possible, pending failure - action required
REASON FOR ALERT
SOURCE: 7 = memory
SOURCE DETAIL: 4 = SIMM or DIMM SOURCE ID: FF
PROBLEM DETAIL: C = checksum error
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH OFF OFF ON
LED State: Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
0x2000006C74FF21C2 0000FF00 0001FF74 - type 4 = Physical Location
0x5800086C74FF21C2 0000670B 0A132324 - type 11 = Timestamp 12/10/2003
19:35:36
A/a: ack read of this entry - Q/q: quit Virtual Front Panel Display
Anything else redisplay the log entry
->Choice:a
*****************************************
memory config 7213
memory config 7214
***** EARLY BOOT VFP : SYSTEM ALERT *****
SYSTEM NAME: unknown
DATE: 12/10/2003 TIME: 19:35:38
ALERT LEVEL: 6 = Boot possible, pending failure - action required
REASON FOR ALERT
SOURCE: 7 = memory
SOURCE DETAIL: 4 = SIMM or DIMM SOURCE ID: FF
PROBLEM DETAIL: C = checksum error
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH OFF OFF ON
LED State: Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
0x2000006C74FF21C2 0000FF00 0002FF74 - type 4 = Physical Location
0x5800086C74FF21C2 0000670B 0A132326 - type 11 = Timestamp 12/10/2003
19:35:38
A/a: ack read of this entry - Q/q: quit Virtual Front Panel Display
Anything else redisplay the log entry
->Choice:a
*****************************************
memory config 7213
memory config 7214
***** EARLY BOOT VFP : SYSTEM ALERT *****
SYSTEM NAME: unknown
DATE: 12/10/2003 TIME: 19:35:41
ALERT LEVEL: 6 = Boot possible, pending failure - action required
REASON FOR ALERT
SOURCE: 7 = memory
SOURCE DETAIL: 4 = SIMM or DIMM SOURCE ID: FF
PROBLEM DETAIL: C = checksum error
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH OFF OFF ON
LED State: Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
0x2000006C74FF21C2 0000FF00 0003FF74 - type 4 = Physical Location
0x5800086C74FF21C2 0000670B 0A132329 - type 11 = Timestamp 12/10/2003
19:35:41
A/a: ack read of this entry - Q/q: quit Virtual Front Panel Display
Anything else redisplay the log entry
->Choice:a
*****************************************
*****************************************
************ EARLY BOOT VFP *************
End of early boot detected
*****************************************
************* SYSTEM ALERT **************
SYSTEM NAME: unknown
DATE: 12/10/2003 TIME: 19:35:43
ALERT LEVEL: 6 = Boot possible, pending failure - action required
REASON FOR ALERT
SOURCE: 7 = memory
SOURCE DETAIL: 4 = SIMM or DIMM SOURCE ID: FF
PROBLEM DETAIL: C = checksum error
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH OFF OFF ON
LED State: Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
0x2000006C74FF21C2 0000FF00 0004FF74 - type 4 = Physical Location
0x5800086C74FF21C2 0000670B 0A13232B - type 11 = Timestamp 12/10/2003
19:35:43
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:a
regards,
joe
-- Joe Brancaleone Support Technician _______________ Nitech 35 Musick Irvine Ca. 92618 Phn: 1-888-264-8324 Fax: 949-586-5234 Email: joe@nitech.com http://www.nitech.com Mission Statement: Nitech is a leader in data management. Our extensive knowledge in both Unix and NT allows us to provide competitive data storage, networking and computing solutions. -- ---> Please post QUESTIONS and SUMMARIES only!! <--- To subscribe/unsubscribe to this list, contact majordomo@dutchworks.nl Name: hpux-admin@dutchworks.nl Owner: owner-hpux-admin@dutchworks.nl Archives: ftp.dutchworks.nl:/pub/digests/hpux-admin (FTP, browse only) http://www.dutchworks.nl/htbin/hpsysadmin (Web, browse & search)
- Previous message: Naylor, Jim: "[HPADM] Insert characters in middle of line"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
