[HPADM] RE: memory question

From: James J. Perry (jjperry_at_water.com)
Date: 05/04/05

  • Next message: Jim Gray: "[HPADM] replacing bad disk in physical volume" 
    Date: Wed, 4 May 2005 11:08:08 -0400
To: <IlicR@stentor.ca>, <hpux-admin@dutchworks.nl>

    I would guess it would be compatible. I have pulled memory from K260s
    and put it in K360s and a K580. It is all generally the same ECC
    memory, so it should work. Just try to make sure that you match you
    memory coming in to be in a/b slots. I/e One simm in 6a the other in 6b.
    This should resolve possible parity issues.

    In my limited hardware reconfig experience (all of our K-class are in
    archive/read only now) I have found that the SIMMs are about the same.
    I also know that someone took K-100 memory and got it working in a
    K-200.

       -Jim

    -----Original Message-----
    From: hpux-admin-owner@DutchWorks.nl
    [mailto:hpux-admin-owner@DutchWorks.nl] On Behalf Of IlicR@stentor.ca
    Sent: Wednesday, May 04, 2005 10:17 AM
    To: hpux-admin@dutchworks.nl
    Subject: [HPADM] memory question

    Due to some unusual situation I have to swap some memory from K 410 to K
    420.
    This is just temporarily solutions until some work on rp* servers is
    done.
    Is this memory compatible or not ? TX in advance for any response.

    PS I know everything is so old.. 

    --
             ---> Please post QUESTIONS and SUMMARIES only!! <---
        To subscribe/unsubscribe to this list, contact
majordomo@dutchworks.nl
       Name: hpux-admin@dutchworks.nl     Owner:
owner-hpux-admin@dutchworks.nl
 
 Archives:  ftp.dutchworks.nl:/pub/digests/hpux-admin       (FTP, browse
only)
            http://www.dutchworks.nl/htbin/hpsysadmin   (Web, browse &
search)
--
             ---> Please post QUESTIONS and SUMMARIES only!! <---
        To subscribe/unsubscribe to this list, contact majordomo@dutchworks.nl
       Name: hpux-admin@dutchworks.nl     Owner: owner-hpux-admin@dutchworks.nl
 
 Archives:  ftp.dutchworks.nl:/pub/digests/hpux-admin       (FTP, browse only)
            http://www.dutchworks.nl/htbin/hpsysadmin   (Web, browse & search)
  • Next message: Jim Gray: "[HPADM] replacing bad disk in physical volume"

    Relevant Pages

    • [HPADM] [HPADMIN] last fails with coredump
      ... "last" command fails with "memory fault" message. ... could be the problem, how to fix it? ... L2000 HP-UX ... To subscribe/unsubscribe to this list, ...
      (HP-UX-Admin)
    • [HPADM] how to figure out the memory used by each process
      ... What is the best feasible command to find out the memory used each process ... ps -e vsz etc. ... To subscribe/unsubscribe to this list, ...
      (HP-UX-Admin)
    • [HPADM] Re: Inetd message
      ... How is your memory doing? ... and how many user sessions? ... To subscribe/unsubscribe to this list, ...
      (HP-UX-Admin)
    • SIMMs and DIMMs Explained - IBM PC
      ... "The 168-pin DIMM is architecturally compatible with the 72-pin SIMM, meaning that the DIMM can be used in some applications to replace 72-pin SIMMs. ... A 'tab' on a memory module is the metal contact at the bottom of the memory module. ... Therefore, there are a total of 144 gold/tin tabs to make contact with the SIMM connector, but only 72 independent signals. ...
      (comp.sys.ibm.ps2.hardware)
    • Re: Strange DRAM module, Want to replace it by 72 pin SIMM, need advice.
      ... The beast has 2 slots filled with strange memory modules. ... strobe the column address for each individual byte, and 1 RAS. ... pretty much like 72pin SIMM, though with only one RAS signal. ... will enable me to use a regular 72 pin SIMM in here. ...
      (sci.electronics.repair)