Re: AlphaStation 200 F4 error

On May 27, 6:22 pm, Rich Jordan <jor...@xxxxxxxxxxx> wrote:
On May 27, 11:10 am, VAXman- @SendSpamHere.ORG wrote:

I'm trying to boot an old AlphaStation. The console initialization
countdown stops at F4. The LEDs on the rear apron of the AS200 also
mirror this code [**** o*oo] F4. I've googled and haven't found any
definitive answer on this code. One document said "reserved to DEC"
which is not very informative.

Any pointers, help, etc. greatly appreciated.

--
VAXman- A Bored Certified VMS Kernel Mode Hacker VAXman(at)TMESIS(dot)COM

"Well my son, life is like a beanstalk, isn't it?"

http://tmesis.com/drat.html

The service doc I have shows the same; 'reserved for future use' but I
did find the following snippet: "When power is applied to the system,
the diagnostic LEDs start decrementing as tests complete successfully
If a test fails, the display does not change. Therefore, when a
failure occurs , the LED code is pointing to the test which last
passed."

That means its test F3 that failed; the service guide says "Load the
DROM code into memory.". F2 apparently continues that, and F1 should
be "Successful load and checksum of DROM".

The popup says that in the event the DROM load fails, SROM will
attempt to load the selected firmware (ARC or SRM), and failing that
will drop into a "mini console" that is apparently available to
manufacturing. Is that the serial port on the MLB in the back? The
docs do not say.

There's also this note: "Check J3: If "normal", then HW_REI to PAL.
If J3 is set to S-Port, go to the SROM mini-console."

That does happen after the test that failed but perhaps the J3 jumper
setting may be worth checking to see if you can get access to further
diagnostics.

I wonder if you have had a firmware corruption. Perhaps even to the
point that you need to use a failsafe boot...

and if by magic on Hoffman Labs
AlphaStation 200 Firmware Failsafe Loader
http://64.223.189.234/node/871
.

Relevant Pages

  • Re: AlphaStation 200 F4 error
    ... The LEDs on the rear apron of the AS200 also ... That means its test F3 that failed; the service guide says "Load the ... DROM code into memory.". ... attempt to load the selected firmware, ...
    (comp.os.vms)
  • Re: AlphaStation 200 F4 error
    ... The LEDs on the rear apron of the AS200 also ... That means its test F3 that failed; the service guide says "Load the ... DROM code into memory.". ... attempt to load the selected firmware, ...
    (comp.os.vms)
  • Re: Newbie Q. re: solar light/battery
    ... The reference to the hare is not to imply that you are an idiot. ... As far as the rest of it goes, first you have the LEDs, and assuming ... Until the cell discharges to its terminal voltage, ... some current into a load with some voltage across the load. ...
    (sci.electronics.basics)
  • Re: LED 101 - light when a plug is inserted
    ... >> Put an LED in series with a 470 ohm resistor across the load, ... >> John Fields ... This would give me LEDs of variable brightness. ... I assumed that the load was in the device into which the ...
    (sci.electronics.basics)
  • Re: [PATCH 4/4] leds: Let GPIO LEDs keep their current state
    ... the GPIO line is. ... On some systems the LEDs are put into some state by the ... I'd prefer firmware to actually update the device tree if the ... and the default-state property is set the to same value, ...
    (Linux-Kernel)
Loading