Re: RS6000 43p/140 AIX 4.3 new install - get stuck!
- From: Dan Foster <usenet@xxxxxxxxxxx>
- Date: Sat, 24 Jun 2006 12:22:45 -0500
In article <1151168580.243829.216790@xxxxxxxxxxxxxxxxxxxxxxxxxxxx>, neomagick@xxxxxxxxx <neomagick@xxxxxxxxx> wrote:
Good morning -
Top o' day. :)
I've recently come into ownership of a well used RS6k 43p model 140
terminal server (and all the serial gear came with it! Very cool!).
Very nice! :)
Just keep something in mind, should you ever get the itch to upgrade it
to AIX v5: 5.1 is the last OS version that you CAN install on the model
140.
With that said, 4.3.3 was a solid OS version, and I've run that on our
former 140 for years without undue trouble.
(If you're really curious about 5.1, they're readily available on eBay,
inexpensively, I seem to recall. 5.2 and later will *DEFINITELY* _NOT_
work on the 140 as they dropped PReP support.)
I've got the manuals for the RS6k, and for the full version of AIX 4.3
that came with it (install guides, network maintenance guides, etc). I
popped a used 4.3gb barracuda drive in, and ran the AIX install off the
CD by a serial console (I've managed to use both the greenscreen serial
terminal that came with it, and my laptop w/ Hypertrm as a console).
The first CD finished up the installation, then rebooted. Now when it
boots, I get the following:
No login prompt, eh? Means your serial cable is not wired properly for
full null modem control. That's a very common issue that trips up the
unwary.
Check the AIX FAQ online (Google search can find it quickly) and read
through the serial cable section. You can either purchase one from a
local electronics store (e.g. Radio Shack in the U.S.) or make the cable
with perhaps USD $2 in parts and about 60 seconds of your time.
There IS a workaround involving 'CLOCAL' and booting off the CD; it is
also mentioned in the AIX FAQ for that procedure. This would hold you
well without needing to obtain the proper hardware.
I've read that the architecture in the system isn't compatible with
x86based hardware (I'm thinking specifically video cards), so I can't,
That's correct. The "BIOS" is very different. This is an issue for any
cards that goes into the system... particularly video card.
So you usually must obtain only cards designed for AIX systems.
With that said, doesn't the 140 already come with a video card? If it
doesn't, you should be able to get one via eBay or some such source.
I've also read that the monitors need to have higher support for the
video being piped down the cable, so an off-the-shelf monitor won't
work with the video coming out of the system.
Nah, they _will_ work with them. Just plug in an ordinary VGA monitor
with a HD-15 VGA connector, and you're all set. :)
If you've got a fancier card with 13W3 outputs, then yeah, you'd need a
monitor with 13W3 cable/connector or some kind of 13W3/VGA adapter.
I'm also curious about the memory. My system has 32mb that it came
with. The manual says it will take up to 768. Is that something a
bios/firmware update would increase? And it doesn't appear to take
Nah, firmware update probably wouldn't increase it. 768 MB is the
maximum that IBM has actually verified will work. It _MIGHT_ be possible
to get higher capacity RAM to work, but you'd be doing it with trial and
error.
If you don't have spare memory or money to try trial-and-error, then
you'd probably need to stick to that if you want to be absolutely sure
you will have a working setup.
768 MB is *plenty* for the 140, even if you run X and Java.
standard dimms - I tried fitting in a few PC-100 sticks that I had
sitting around, but the notch nearest the smallest grouping of contact
points is just slightly off from the stick from the system. Does it
not take standard ram? Do I need to buy a special form?
You usually have to buy ECC RAM for these machines (even for the
'workstations'). I don't have the specs for 140's memory offhand but
should be able to find it via a search online. If nobody here knows
offhand, I can look it up.
I would also advise against trying to force the RAM you have, because it
is likely not just non-ECC... it is probably also the wrong voltage.
That notch you refer to, is slightly offset, if you try to plug it into
the wrong voltage motherboard. It fits only if you plug it into the
correct voltage motherboard.
(There are newer 3.3V DIMMs and there are older 5V DIMMs.)
My apologies for the barrage of questions - I'm very keen to get this
up and running!! Thanks very much for your help!
No apologies necessary. We've all been where you are now. :) You're
also asking good and well-reasoned questions.
Cheers,
-Dan
.
- Follow-Ups:
- Re: RS6000 43p/140 AIX 4.3 new install - get stuck!
- From: John-Luke
- Re: RS6000 43p/140 AIX 4.3 new install - get stuck!
- References:
- RS6000 43p/140 AIX 4.3 new install - get stuck!
- From: neomagick
- RS6000 43p/140 AIX 4.3 new install - get stuck!
- Prev by Date: RS6000 43p/140 AIX 4.3 new install - get stuck!
- Next by Date: Re: RS6000 43p/140 AIX 4.3 new install - get stuck!
- Previous by thread: RS6000 43p/140 AIX 4.3 new install - get stuck!
- Next by thread: Re: RS6000 43p/140 AIX 4.3 new install - get stuck!
- Index(es):
Relevant Pages
|
|
